Turn the Isolation Switch Shut off your system by hitting the isolation switch, wait 30 to 60 minutes and then turn it back on. This manual reboot fully disconnects your AC unit from power, allowing all electrical components to reset.
Use the Reset Button on AC Unit
Don't worry; the reset button might be able to solve the issue after a sudden disconnection or power outage. You can press the “Reset” button on the air conditioning unit, often shown as a small red button, to bring your air conditioning unit back to life.
Not all air conditioning units have a reset button, but if yours does, it's typically located on the outdoor unit. Here's how to locate it: Turn Off the Power: Before you search for the reset button, ensure the power to the unit is turned off for safety reasons.
Faulty Wiring
If the wiring between the thermostat and the air conditioning system is faulty, the system may not turn on. This can happen if the wiring is old or if it has become damaged over time. To fix this issue, you may need to call a professional HVAC technician to inspect and repair the wiring.
For safety reasons, always turn off the main power supply before resetting the AC circuit breaker. Resetting precautions and electrical safety are crucial to avoid potential hazards or damage. Always prioritize safety when dealing with electrical components.
Shut off your system by hitting the isolation switch, wait 30 to 60 minutes and then turn it back on. This manual reboot fully disconnects your AC unit from power, allowing all electrical components to reset.
Check the thermostat
You should check if it's been set to the correct temperature and also make sure it's set to “cool”. If the AC settings are not right, it won't turn on. You can also check if the batteries in the thermostat are fresh and replace them if needed.
If your AC is running but not cooling, it could be due to a dirty air filter, incorrect thermostat settings, a malfunctioning thermostat, a refrigerant leak, dirty condenser coils, blocked vents or ducts, a faulty compressor, frozen evaporator coils, or electrical issues.
A bad thermostat can be detected when your AC or furnace is not turning on, your HVAC systems are not turning off, the thermostat not responding, your HVAC system is short-cycling, the room temperature not matching the temperature displayed on the thermostat, and the programmed setting resetting themselves.
Any time you are having an issue with heating and cooling units, such as after a sudden power failure or after your children have had 'control' of the system while you've been away, resetting the thermostat should be the first thing you try when attempting to rectify HVAC system issues.
It's a small, red button usually located on or around the unit. The button should have a clear 'reset' label. Once you find the button, press it for around three seconds and observe the AC. Check whether the AC kicks on immediately and if it doesn't, press the button again for another three seconds.
Your AC unit may in fact have its own reset feature already. This feature will likely perform this entire process for you when selected.
A tripped circuit breaker can be a major cause of why an outside AC unit isn't turning on. This occurs when the current is too high in the outdoor unit, causing the breaker in the fuse box or main electrical panel to switch off power to the unit, resulting in it not receiving any electricity.
Circuit breakers can be found in homes, businesses, and industrial facilities. They are typically located in the main electrical panel, which is typically located in the basement or garage.
Try checking the circuit breaker box or replacing the batteries. Bad wiring: The thermostat may be unresponsive if the wiring has gone bad. Remove the cover and check inside for loose, detached, or corroded wires. If you spot any problems, contact an HVAC technician for assistance.
The thermostat is the central control of your HVAC system, and malfunctioning can prevent the AC and furnace from turning on.
One of the most obvious signs that your home's thermostat needs replacing is that it has faulty temperature readings. You'll notice that the indoor temperature reading is nowhere near what it actually feels like.
There are a number of reasons why your air conditioner might be running but not cooling. It could be an issue with the thermostat, the compressor, or the evaporator coils. Or, it could simply be clogged with dust and debris, which is preventing it from working properly.
When you notice that your air conditioner isn't cooling, your first action should be to turn it off. This might seem counterintuitive—after all, you want your home to be cool. However, continuing to run an AC that isn't effectively cooling can cause further damage to the system.
In AC systems, the air conditioner reset button is on the outside unit's lower edge, typically close to the ground. Some models have the reset button located behind the service panel, which may require tools to remove. Reset buttons are usually red or yellow with a clear “reset” label.
Check Your Circuit Breaker
Locate your main circuit breaker and switch it back to the "On" position. Wait 30 seconds and turn on your air conditioner again. If it still doesn't work, you'll need to call a professional for help.
Check these issues when the unit won't kick on: Check the thermostat and adjust the settings if it isn't set to Cool and an appropriate temperature setting to call for cooling. Examine the house circuit breakers for the AC unit and reset any tripped breakers. Check the air filter and replace the filter if it's dirty.