A bad ignitor usually causes your appliance to click repeatedly without starting, emit a buzzing sound, or blow cold air. For a definitive test, turn off the power, detach the ignitor wires, and use a multimeter set to ohms to check for resistance (typically 40 to 400 ohms); an infinity or "OL" reading means it is dead.
A furnace ignitor typically lasts 3–5 years and costs $30–$100 for the part, with professional installation running $150–$300 total.
A bad hot surface igniter (commonly used in furnaces and ovens) may show a physical break, hairline fracture, white burnt-out lines, or dark scorched spots. In many cases, it will simply fail to glow bright orange-yellow when the appliance attempts to start, or it will only glow dimly.
To clean a clogged or dirty gas stove igniter, first unplug the stove and let it cool. Locate the small ignition port or gas hole, and use a paperclip, needle, or toothpick to gently clear any trapped food or grease. Next, gently wipe the igniter's metal tip with a cotton swab dipped in rubbing alcohol to remove carbon buildup.
Yes, you can absolutely replace an ignitor yourself. Whether it is for a gas oven or a furnace, it is a very common and straightforward DIY repair that requires basic tools like a screwdriver and wire strippers.
A furnace ignitor typically lasts between 3 to 7 years. However, the exact lifespan largely depends on the material, your furnace's usage, and how well you maintain your system:
The most expensive thing to fix on a furnace is the heat exchanger. Replacing it typically costs between $𝟏,𝟎𝟎𝟎 and $𝟑,𝟓𝟎𝟎, primarily because it is a highly labor-intensive job that involves virtually dismantling the entire unit.
It's possible for a furnace to still run with a faulty ignitor, yet the air coming from the vents will be cold, not warm. Unless the ignitor lights the burners to burn fuel, your furnace won't have warm air to distribute around your home or business.
To reset a furnace ignitor, you generally need to perform a system power cycle to reset the control board after an ignition failure. There is rarely a dedicated "reset button" just for the ignitor itself.
The "$5,000 rule" is a quick, rough guideline to help homeowners decide whether to repair an aging furnace or replace it entirely. It helps you determine if pouring money into an old system is a waste of cash, or if it still has plenty of life left.
To force your furnace to start, check the thermostat settings and make sure they are calling for heat. Then, verify the power sources, including the main circuit breaker, the safety power switch near the furnace, and the access panel door. Finally, replace any clogged air filters.
The Short Answer Is: Warning signs of a bad furnace ignitor include the furnace not starting or heating, a noticeable clicking sound without ignition, or frequent short cycling where the furnace turns on and off rapidly.
While damaged ignitors may retain some normal function and only sporadically fail, some may fail altogether. The furnace may attempt to start but shut down after a few seconds, and the ignitor may glow but fail to light the burners or not glow altogether.
Replacing a furnace igniter generally costs between $150 and $425 for professional repair, with an average, common total around $300–$350. The part itself is inexpensive, costing only $20–$100, while labor makes up the remainder of the cost. DIY replacement is often possible for under $100.
What fails first on a furnace? The most common early failures are the furnace ignitor or flame sensor, as they experience regular wear and tear and are critical to starting the heating cycle.
If your furnace breaks and you cannot afford the repair, act quickly to stay warm and access emergency assistance. First, call your local 2-1-1 or visit 211.org to find emergency utility assistance. Next, apply for LIHEAP to receive federally funded help for home heating crises and equipment repairs.
A furnace typically lasts between 15 and 20 years. However, the exact lifespan varies based on the type of unit and how well it is maintained.
Furnace ignitor failure is usually caused by physical fragility, electrical issues, environmental stress, or normal wear and tear. Because igniters heat up and cool down thousands of times, they naturally degrade over time, typically lasting between 3 and 7 years.
At 10 years old, your furnace is likely just entering the second half of its lifespan, as most well-maintained units last 15 to 20 years. Fixing it is almost always worth it if the repair is minor, the part is under warranty, and you haven't had a history of frequent breakdowns.
Yes, you can replace a furnace ignitor yourself if you are handy. The part costs between $30 and $100, making it a very DIY-friendly task that takes about 151515 to 303030 minutes. However, it involves working with gas and electricity, so caution and precision are required.
Types of furnace ignitors
Newer furnaces have an electronic ignition system. The most common type is the hot surface ignitor (HSI). Ignition happens in a sealed combustion chamber to protect you from exhaust fumes.
At 7 years old, an oven is right on the bubble. Generally, if the repair cost is less than 50% of the price of a brand-new comparable oven, it is financially worth fixing. Otherwise, it is usually smarter to replace it, as the appliance is nearing the back half of its expected 10-to-15-year lifespan.
The cost to fix furnace ignitor typically ranges from $150 to $425 for professional replacement, including both parts and labor. Here's what you can expect to pay: Quick Cost Breakdown: Ignitor part only: $20-$100.