Brushing thoroughly 1-2 times per week will prevent these materials from having the time to create a stain. Brush to Prevent Algae: Every pool can grow algae, but plaster, quartz, and aggregate finishes are more susceptible.
After a swimming pool installation, or when it is replastered, you'll want to brush much more often. Brush it twice a day for the first two weeks and then move to a standard schedule. Every time you add chemicals to fix the pool's balance, it's important to brush it. It helps the chemicals dissolve evenly.
Algae will stick to the walls of your pool and may leave stains if not scrubbed away properly. The walls need scrubbing weekly. A slick surface texture on the pool walls indicates that you need to clean them. Always brush your walls after vacuuming the bottom of the pool to prevent stirring any dirt on the floor.
Brush the pool twice a day for the first two weeks. This opens the pores of the plaster to allow proper curing as well as removes any loose plaster dust from the surface. You may notice plaster dusting when you brush and the water becomes cloudy. This is normal and will go away with proper treatment and brushing.
BRUSHING THE POOL
It is recommended that the pool be brushed with a standard 18-inch nylon bristle pool brush at least twice per week. The entire process usually only takes 10 minutes and is well worth the time and effort.
It is important to brush you pool daily. This can be time consuming so if necessary, alternate two walls one day, the other two the next day, and the floor the next day. This way, your whole pool is getting brushed almost two full times per week.
What happens? They stain! The dirt gets embedded in the fabric and the jeans take on the color of the dirt. The same is true of your plaster, pebble, quartz, hydrazzo and various other finishes: if you don't run a brush over the surface regularly it will stain.
Chlorine/non-chlorine chemicals – When adding chlorine or non-chlorine chemicals to “shock” your pool after a fill-up, wait about 24 hours or until levels are approximately 5 ppm. If you'll only be adding liquid chlorine, it's generally safe to swim after about 4 hours or until levels are 5 ppm or lower.
Brush the entire pool surface, from the top of the walls down, starting at the shallow-end and ending at the deep-end. Brush thoroughly twice per day to remove all plaster dust. Brushing your pool finish at least twice a day is one of the best things you can do to maintain the gorgeous appearance of a pool finish.
Brushing thoroughly 1-2 times per week will prevent these materials from having the time to create a stain. Brush to Prevent Algae: Every pool can grow algae, but plaster, quartz, and aggregate finishes are more susceptible.
In a nutshell, a no-drain acid wash is lowering the pH level of your pool so that your pool water becomes acidic and alkalinity close to zero. When this level is hit, some vigorous scrubbing will be required to peel off a bit of the pool surface, essentially giving you an acid wash without draining the pool.
Mustard algae and most yellow/brown algae will like the bottom of the pool. The fastest way to get rid of these stains is to apply chlorine straight onto the discoloration. Scrub with a brush and watch it disappear. Run a water test to see what other stuff might be in the water, and treat accordingly.
In general, it's a good idea to vacuum your pool once a week. You should also vacuum your swimming pool any time you notice large amounts of debris, dirt, or leaves on the floor of the pool (for example, your pool may need vacuuming after a heavy storm).
Acid washes are ideal for minor discolorations caused by things like leaves falling into the pool. The main benefit of acid washing, during some new finishes application is to remove any haze or cement residue.
At first you'll add chlorine in what's called “shock” levels – an extra heavy dose to start your pool off. A shock dose coupled with extra circulation will ensure that all the water gets treated properly in the beginning.
Your first instinct when you fill your pool with new water, is to shock it. But that shock then oxidizes the metals, that chemical reaction then causes the green hue in your water. This is common with refills that used well water or even water that hasn't been shocked but instead contains a high level of metals.
It's an absolutely vital step in the pool cleaning process, but initially, it feels like a step backwards. Brushing is very effective to kick up settled particles so that the skimmer and drain have an opportunity to collect them.
So, as we all know, swimming pools, whether common or privately owned, need to be cleaned on a regular basis to prevent bacterial contamination, algal growth, dirt, excess chemicals, and other things.
Green algae can be easily gotten rid of using chlorine, algaecides and the right water flow process. Those that grow on the side of the pool can be brushed off and the water filter run to eliminate it from the pool. With the right water pH, green algae can be prevented and even killed off.
Clean the Filter
The slimy feel on your pool walls is an early indication of algae growth. To stop algae growth in its tracks, clean the pool filter first. Before adding any chemicals to the pool, make sure you have a clean filter.
Only pools constructed of plaster, exposed aggregate, or concrete are strong enough to withstand the power of a pressure washer. Any other type of pool, such as vinyl or fiberglass, must be cleaned using chemical treatments or using non-abrasive methods.