Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter's pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
Whenever the filter fills up with the dirt/debris it reduces the flow of water to your pool. Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear.
To begin vacuuming your pool:
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.
Set the valve to Rinse. Depress the valve selector handle, then turn it to the Rinse setting. After a backwash, sand and debris becomes unsettled settle in the filter's internal plumbing. The rinse setting returns to the normal path through the filter, flushing debris to waste.
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
Backwashing a filter too frequently will keep the sand so free of dirt buildup that it will not have the ability to remove the smaller particles of dirt and they will simply pass through sometimes causing cloudiness in water.
Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day. But here's the thing: you don't have to run your pool pump consecutively. You can choose to run it for three hours in the morning before you leave for work and another 5 hours in the evening.
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value's waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
If you see it blowing out into the pool, something is broken. The most common problem is a cracked lateral, which is one of the perforated pipes at the bottom of the filter that catches water that has circulated through the sand.
Too much sand and your filter will likely not run correctly or may break when reassembling. Too little sand and you will have cloudy water no matter how much your filter runs. For this reason check your filter manufacturer's specs.
Pool filter sand should not be reused because the roughness of the particles that is used to catch unwanted bacteria, contaminates, and debris will be too worn down to be effective. Reused pool filter sand can result in severe contamination of your pool and is not worth the risk.
In general, it's a good idea to vacuum your pool once a week. You should also vacuum your swimming pool any time you notice large amounts of debris, dirt, or leaves on the floor of the pool (for example, your pool may need vacuuming after a heavy storm).
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool's size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool's turnover rate is.
After a backwash, to get the amount of DE powder, simply take the recommended amount of DE powder for a new filter and multiply it by 0.8, or 80%.