You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
Adding too much DE to your pool may cause multiple negative results. These ramifications include a clogged skimmer, turning the pool cloudy, reducing the circulatory pressure in the pool and putting too much work on your pump that may result in eventually breaking the pump.
If you are replacing DE Powder after a backwash, you will not need to add the full amount - generally around 80%. The grids will have retained some of the DE Power after the backwash, and if you add too much, it may end up in the pool. The best way to assess how much DE Power to add is to monitor the pressure gauge.
The D.E. needs to be replenished once the filter is turned back on. Every three months the filter should be taken apart, the grids should be hosed off, and visually inspected for any rips or tears that will cause D.E. to blow back into the pool.
Small amounts of DE can be added to a sand filter after each backwash to improve the filtering. The first time you use DE, you need to figure out how much DE to add to your filter. After the first time, you can simply mix the full amount of DE with water in a bucket and pour that slowly into the skimmer.
After a backwash, to get the amount of DE powder, simply take the recommended amount of DE powder for a new filter and multiply it by 0.8, or 80%.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Run your filter 24 hours a day and backwash 3 or 4 times a day for quickest results. Green or cloudy water will quickly clog a filter, therefore you may have to backwash your filter many times a day until the pool clears. THIS IS NORMAL ! Remember, you cannot over-backwash a pool filter.
If you do not add enough DE to your filter, then the grids are not totally coated with DE and the dirt that goes into your filter will attach itself right to the fabric on the grids and will not backwash off. This will cause your filter to short cycle (go very short times between backwashing).
After the hose fills with water, backwash your sand filter for 2 - 3 minutes, or until water runs clear. Shut off the pump motor and push the T-handle back down into locked position. Turn your pump back on and note the lower pressure.
Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.
A DE Scoop is specially designed to measure DE powder and 1 scoop is equal to 1/2 lb. of DE powder. To determine how many scoops or coffee cans of DE your filter requires take your filter square footage and divide by 5 (this would be after a full cleaning).
DE Blow-Back: If DE powder is coming into the pool, you may have torn filter grid fabric. Or, you could have a cracked top manifold, or missing air bleeder. The standpipe o-ring could be missing, or the filter valve could be allowing some DE powder to bypass the filter as you add it new.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
Turn on the pump and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear. Turn Off the Pump. Set the filter valve handle to the RINSE position and ensure the handle locks in place.
DE filters are usually torn down and cleaned at least six times per year. Unless your pool gets really dirty, you should not need to backwash it beyond your scheduled maintenance. Another theory recommends to backwash when the pressure gauge is about 8 to 10 psi (pound-force per square inch) over the starting level.
As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter's pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.
You should clean your DE filter at least once every month or whenever you're pounds per square inch is 8 to 10 pounds above the normal starting pressure. Cleaning your DE Filter involves three basic steps: Backwashing, Cleaning the manifold and grid and adding new DE.
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
This leaves your pool a cloudy, muddy-looking mess. Luckily however, the powder usually sinks to the bottom of the pool. The only way to remove the earth from your pool is to vacuum the pool with the filter release valve open. This will allow the earth to flush from the filter.
Those with DE filters are probably extremely happy with the quality of water that a DE filter creates, but there comes a time when you will need to replace the filter grids. This is usually after 7-10 years of hard work.