The average family could save 2,700 gallons per year by installing WaterSense labeled showerheads. Since these water savings will reduce demands on water heaters, they will also save energy. In fact, the average family could save more than 330 kilowatt hours of electricity annually, enough to power a house for 11 days.
Install Flow Restrictors
Flow restrictors belong on all bathroom and kitchen faucets. Each one can save you up to 5,000 gallons, or about $10 every year.
Benefits: Low flow shower heads can decrease water consumption by 40% or more! This not only conserves water, but it cuts down on your monthly water bill providing significant end-of-year savings. Showers take energy to heat the water, thus cutting down on water usage also cuts down on energy usage.
In applications where a large volume of water is used, such as showers and water filtration systems, a flow restrictor can save you money on your water bill each month. Flow restrictors can be applied to all bathroom and kitchen faucets, and they must be used for reverse osmosis filtration systems.
A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
After all, it needs certain amount of water to remove the soap, that is physic. Studies have shown that 1.8 gpm is the minimum flow rate to have a good enjoyable rinsing, so the common 1.75 gpm models, is somewhat good enough for a decent shower. To save water further and still have a full enjoyable rinsing experience.
Unfortunately, there is no firm definition of low-flow, but it's generally accepted that anything using 1.5 gallons per minute (gpm) or less is considered “ultra low flow,” while anything using 2.5 gallons per minute to 1.5 gallons per minute is considered “low flow.” Nowadays, thanks to standards set by the government ...
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992.
Decreased water waste - Low flow fixtures are specifically designed to limit water waste. The average low flow fixture expels around half the gallons per minute than a standard fixture. Add that up over time, and you can save about a thousand gallons of water per year!
The average bath uses about 80 litres of water. Over the course of four minutes a normal shower head produces about 36 litres.
Low-flow showerheads and faucets cost $10 and upward, and they can reduce your water use by 30 percent to 50 percent. Resulting savings in water use and hot water heating can be $50 to $90 or more a year, just by installing a couple of water-saving fixtures.
While it is possible to remove flow restrictors from shower heads, we strongly advise against it for several reasons. Flow restrictors for faucets are an integral part of most aerators and it is generally not possible or desirable to remove them.
There are two types of "low-flow" heads available. Non-aerating ones work by restricting the water flow and squeezing it through very small holes; this produces quite a hard, massaging water spray. "Aerating" heads, meanwhile, mix oxygen with the water to create a softer, bubbly, shower.
That's why it pays to invest in a quality low flow eco shower head that not only saves water but does it without making your shower feel like a drudge and no fun at all. A well-manufactured shower head from a trusted brand will reduce water consumption by up to 60%, which is a big saving year on year.
If your showerhead is labeled 2.5 GPM or less, you have a low-flow showerhead. Any showerhead labeled 2.6 GPM or above is a high-flow showerhead. If your showerhead doesn't have a label, try this trick to determine the flow rate. Place a bucket or container with a 1-gallon marker under the showerhead.
Standard shower heads use 2.5 gpm, but to earn the WaterSense label, a product must use no more than 2 gpm and still meet strict performance requirements. The EPA estimates that the average family could save 2,900 gallons of water per year by installing a WaterSense-labeled shower head.
Absolutely. Many low-flow shower heads still deliver a powerful, satisfying shower even with a reduced flow rate. If you're looking for a better showering experience that also helps you save water, we recommend checking out the 1.8-GPM shower head model from hai.
Since 1992, a maximum of 2.5 GPM is the EPA-mandated flow rate for new showerheads. This means that no more than 2.5 gallons of water should be flowing out of your shower head at any given minute. Additionally, manufacturers have decreased the flow rate for showerheads over time.
Efficient shower heads use at least 1.5gpm. Taking the same amount of time in the shower uses only 15 gallons of water. The water savings amount up to 65 gallons of water!
Areas indicating a maximum flow rate of 4.0 gallons per minute or more are generally satisfactory for running 2 showers at a time with standard showerheads.
A low- flow shower head costs approximately $30-$40, is easy to install and can be used on all pressure systems.
There are low-flow showerheads for every price range, but most cost between $50 and $100. You can get a basic low-flow showerhead for less than $20, but a luxury showerhead could cost more than $1,000. Also factor labor into your shower hardware budget.
Because they're so much bigger than the average showerhead, but still provide the same amount of water (which can vary by water-saving mandate depending on where you live), it's just math: The same amount of water delivered across a bigger surface = less pressure.