Well inspections run between $300 and $600 for an average cost of $450. A pro can offer a more accurate estimate for your well based on its type, depth, and other factors.
A well inspection costs $250 to $550, depending on the well type, depth, and age and whether the inspection includes water testing. Laboratory well water testing alone costs $100 to $350 on average.
How is the test done? A well flow test is conducted by connecting a measuring device to an outside spigot and measuring the flow of water over a defined period of time.
How Much Does a Well Inspection Cost? An average well inspection ranges from $300 to $500. This depends on the inspector's rates as well as the type of water tests they intend to conduct to check water quality. It also depends on whether they provide a septic inspection as well.
Well drilling costs $15 to $25 per foot for the drilling process only. Installing a complete well water system costs $25 to $65 per foot, irrigation wells run $50 to $100 per foot, and geothermal wells are $15 to $40 per foot. *Prices typically include drilling, pump, casing, and complete installation.
An annual well maintenance check, including a bacterial test, is recommended. Any source of drinking water should be checked any time there is a change in taste, odor or appearance, or anytime a water supply system is serviced.
5 gpm (two fixtures running simultaneously at 2.5 gpm) is a good estimate of peak demand, for the typical household. Water wells that reliably yield 5 gpm should be able to meet peak and daily needs for most residences. Wells yielding less than 5 gpm, however, are sometimes the only water source available.
A pro can offer a more accurate estimate for your well based on its type, depth, and other factors. The cost of a well inspection ranges from $150 to $900, with most people paying around $450. Your total cost will depend on factors like the type of well you have, its depth, and your location.
So to recap; homeowner's insurance does not normally cover pump replacement or servicing. If it does, it's probably due to weather anomalies that would also have ended up damaging a significant portion of your home. You'll need to check your specific policy for a weather peril clause.
Some counties offer free well water testing, so check with your county first. If they don't, use this EPA website to find a list of state-certified laboratories in your area that do water testing, or contact your county or state health department or your State Certification Officer for assistance.
A typical inspection normally takes 1 ½ to 2 hours, and we run the water for up to an hour as needed.
You may be told to drink about 4 glasses of water several hours before the test to be sure that your bladder is full. Don't empty your bladder before arriving for the procedure. If you are pregnant or think you may be, tell your healthcare provider.
When the pump turns on, immediately close the spigot and time the period it takes for the well pump to recover, that is, between cut in and cut out. The formula for determining the flow rate is gallons drawn down that were measured above, divided by the seconds required for recovery, then multiplied by 60.
Importance of Water Quality Testing
Well Flow Tests are important for determining the flow rate of water from a well and identifying any potential problems with the well or surrounding aquifer. However, it is equally important to test the quality of the water.
Homeowners with municipal water pay for their water service, which includes testing and maintenance fees. In a home with a private well, maintenance and water testing are the homeowner's responsibility.
While a well pump can last 40 years or more with exceptional care and maintenance, most pumps have a typical lifespan of 8 to 15 years. Regular inspection and servicing can help extend the pump's lifespan.
Most well pump replacement projects fall between $975 and $2,575, but many factors can add additional costs. A small hand pump can cost as little as $200, while a high-end constant-pressure well pump could set you back as much as $5,000.
Well failure and repair are covered by homeowners insurance if the damage or failure was caused by a covered peril, such as lightning or a hurricane.
A well inspection includes checking all of the well components, water pressure flow rate, water level before and during pumping, pump motor performance, pressure tank performance, and well water quality. Well inspectors measure the volume of water pumped and the rate at which the pump works.
The cost of a primary care visit without insurance generally ranges from $150-$300 for a basic visit and averages $171 across major cities in the United States. For any additional services such as childhood and adult immunizations, lab testing, or prescriptions, there will be additional charges.
Test water every year for total coliform bacteria, nitrates, total dissolved solids and pH levels, especially if you have a new well, or have replaced or repaired pipes, pumps or the well casing.
In general, you should expect your well to replenish at a rate of 5 gallons per minute, but there are a number of factors that will play a role in how quickly it refills. For reference, if your well is 1200 gallons, it should take approximately 4 hours to refill.
You can fill a pool with well water if the well and water meet certain conditions. Well water is usually free, convenient, and does not have added chemicals. It may contain bacteria or contaminants, and it can flow slowly or run dry. Before putting well water in a pool, know the pool size, flow rate, and if it is safe.
Standard Hydrofracturing service to a residential well will run in the $2000 to $3000 range by the time everything is put back together and finished. Zone fracturing service to a residential well will usually run in the range of $5000 to $7000 when finished and put back together.