A 20x20 brick paver patio costs $3,800 to $6,800. The average cost of pavers and base materials is $4 to $6 per square foot, while labor runs $6 to $11 per square foot. Get free estimates from masonry contractors near you or view our cost guide below. How much will your paver patio cost?
Or an estimated $4 to $11 per square foot. So labor costs for our sample patio could be anywhere from $1,600 to $4,400. When you combine all the elements needed to create a paver patio of 20' x 20' then the price could range from $2,925 to $21,005.
How Much Does a 20x20 Paver Patio Cost? According to data from HomeGuide, a 20-foot by 20-foot paver patio runs from $1,900 to $6,800, including labor and materials such as clay brick, natural stone or concrete pavers. Obviously, the larger the patio, the more materials required and the greater the labor costs.
As far as installation costs and concrete costs go, poured concrete is technically the most affordable per square foot. However, even though the upfront cost of pavers is higher, concrete pavers offer greater value and durability than poured concrete and stamped concrete.
To install a 400-square-foot paver patio, most homeowners spend between $3,476 to $8,872. Homeowners can expect to spend between $3,476 and $8,872 for a 400-square-foot paver patio (or $8.69 to $22.18 per square foot). Most homeowners spend an average of $4,537 to install a paver patio (or $11.34 per square foot).
While there are no hard numbers on it, this suggests that a paver driveway would be a good option to increase the value of your home. Like other exterior changes, adding pavers can make a dramatic impact on the curb appeal of your property, which can improve its value and shorten the time that it is on the market.
When it comes to costs, patios are often cheaper and easier to build but depending on the location, a deck may be a more valuable upgrade to your outdoor living space.
Pavers have a higher resale value because of their beauty and versatility. Concrete slabs are generally more common, but over time, pavers will net you more value because concrete is expensive to replace.
A properly installed and maintained concrete paver driveway can be expected to last 25 to 50 years.
A typical 24x24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
The base cost of material for a 30×50 concrete slab is between $2.83 and $5.47 per square foot. The total cost may range from $4,245 to $8,205. However, hiring a contractor may cost between $6 and $8 per square foot, bringing the price range to $9,000 to $12,000. The biggest cost is the material.
For example, for a concrete slab that is 24' X 24' X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
Concrete costs between $6 and $12 per square foot, installed. On the other hand, pavers typically cost $8 to $25 per square foot, including installation. For some high-end pavers, you can pay as much as $50 per square foot.
Concrete is one of the most popular patio materials and the cheapest material you can use to build a hard-surface patio. Concrete is made of aggregates and paste—concrete aggregates can be crushed stone, sand, gravel, or even shells; the paste is made up of water and cement.
Fortunately, you can put pavers directly over existing concrete. It's a common practice and a great way to upgrade your concrete surfaces. While mortar is preferable when installing pavers, it's possible to put in the pavers without mortar (although it puts you at risk of drainage issues and cracking).
Paver Square Footage
In this case, 144 divided by 32 is 4 1/2 pavers per square foot. Multiply that number by the area square footage; if you have 100 square feet to fill, you need at least 450 pavers.
There are approximately 38 pavers per square metre, but this varies due to the number of cuts and the laying pattern chosen. You will also need to allow for wastage. The quantity of pavers needed will depend on the area to be paved, and the paver chosen. Work out the area to be paved in square metres.
When homeowners invest in a paver patio, they can expect extreme durability, minimal maintenance and — you guessed it — added value to their home. According to Inman, a leading real estate news source, patio additions to homes (when done properly) can deliver a return on investment of anywhere between 30% to 60%.
Meanwhile, pavers are incredibly durable and it's easy to replace individual stones as needed, so the maintenance costs are lower over time and the stones will last much longer than the concrete surface.
A layer of gravel, compressed down over the soil and add a thin layer of sand on the gravel and smooth it to make it level. This offers a stable base for the pavers.
The average homeowner spends $2,200 to build a 10x10 foot deck, $6,160 to build a 14x20 deck, and $8,800 to build a 20x20 deck. The cost to build a deck with pressure-treated wood, hardwood, or composite is about $25 per square foot, for both materials and installation.
Concrete is one of the cheapest and most popular materials that can be used to build a hard-surface patio. The aggregates of concrete can be stone, gravel, sand, or shells, which are mixed with water to form a paste that dries into a hard surface when left to settle.
Decks can provide a great view, while patios tend to offer more privacy. The views from your deck or patio depend on your home's location and surrounding environment. However, decks usually offer better views than patios due to their elevation.