So how often do you need to replaster a pool? The short answer is about every 10 years. However, it's important to consider the factors mentioned above, as they are typical signs that your pool needs to be replastered.
Extent/properly replastered
Some contractors will put a bond coat over your existing plaster without performing a quality check of the existing shell to determine if the existing plaster is loose/hollow. It is common for water to remain between layers of plaster in a pool when it is first drained.
That's perfectly normal. Depending on a variety of local factors and your individual pool-water treatment routine, the typical lifespan of traditional marcite plaster is 7 to 10 years. If the finish includes a quartz aggregate blend, the time table should extend another five years.
Pool resurfacing or replastering should be done every 10 years. This is based on the surface lifespans of cement and pool plaster material. But constant use, chemical exposure, and climate changes can damage the pool plaster. That said, you should consider resurfacing your pool every 3 to 7 years.
The typical cost to have a pool replastered is between $4 and $7 per square foot. Assuming an average pool size of 16 feet by 32 feet, 4 feet deep on the shallow end and 8 feet on the deep end, that's total of 1,088 square feet. If the cost is $5 per square foot, replastering would cost $5,440.
A concrete (gunite) pool lasts 10–15 years before it needs to be resurfaced. In addition to redoing the interior finish, you'll usually need to replace the waterline tile at the same time.
On average, gunite swimming pools last 7 to 10 years before they need to be resurfaced. When that time comes, it's important to know what options are available so that you can pick the best choice for your backyard space.
When you are swimming, you would get scratched or roughened when you step out of the pool. Also, you could get scratched or your swimsuit could get torn with the jagged plaster. If it's unpleasant to run your hand along the side of the pool or climb up the stairs then its because your plaster is wearing thin.
I. If the pool ever needs to be drained to replace the water or to maintain the plaster, it should never be left empty for more than eight to ten days at the most. More than this may cause the plaster to dry out and crack. Keep your pool full for best results.
wait at least 14 days before heating the water and monitor chemical balance more closely after you turn on your heater.
Yes. The thinset and grout used to install the new tile will fall onto the pool surface. This is not easily brushed off. The pool will likely have to be pressure washed and possibly acid washed after the retile if you are not replastering the pool as well.
What Is It? Gray (or grey) mottling discoloration is due to high amounts of calcium chloride added to a plaster mix, and or late, hard and dry troweling. This issue has nothing to do with the water chemistry or the way the pool was originally started up with chemicals when initially filled with water.
Apply a bead of underwater sealer along the edges of the crack. Leave about ⅜ of an inch of space for the plaster you'll use to fill the crack. Mix the pool plaster with the included bonding agent until it has the consistency of peanut butter—thick enough to stay in place, but not so thick you can't easily spread it.
Diamond Brite® finishes are blends of selected quartz aggregates and fortified white Portland cement ideal for new or re-finished swimming pools. Diamond Brite® finishes are factory blended to provide the pool owner with an extremely durable and attractive alternative to traditional pool coatings.
Advantages: Tile is the longest-lasting interior finish for a concrete pool. Tile is easier to clean than exposed aggregate.
So, when a client requests a new pool surface, the pool remodeling industry refers to that as pool resurfacing or replastering. Since the project focuses on the interior surface — the walls and floor of the pool — price can vary.
Thanks to its relatively simple look and material makeup, pool plaster is a lot less expensive than Pebble Tec®. White plaster costs about $4 for every square foot of pool surface. Meanwhile, a pebble finish, like Pebble Tec® or Pebble Sheen®, can easily cost $10 or more per square foot.
One major thing to remember is that pool plaster can change colors or overall look as it sets and cures. Plaster is hand applied, so it is normal to expect slightly uneven areas, and the color will not be 100% uniform throughout the pool. Also, as the plaster cures, the appearance will change slightly.
Applied at a thickness of about one half an inch, white plaster was the standard in the pool industry.
How long does it take to resurface a pool? Pool resurfacing usually takes about 5-7 days to complete. The pool resurfacing process can be hindered by weather, however, and may take up to 14 days in certain cases.