Dries to the touch in 30 minutes, can be recoated in 1 hour. Full adhesion and hardness develops in 7 days. Lower temperatures, higher humidity, and the addition of tint will prolong dry and cure time. Allow more time at cooler temperatures.
Dries to touch in 5 minutes and can be topcoated in 30 minutes with latex or oil-based paints. For best results, allow primer to cure overnight before applying strong solvent- based topcoats. Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits.
Application– Ready to use - no dilution necessary. In most cases only one coat is necessary. Porous surfaces may require two coats to properly seal. Prime entire surface for best results.
Hello, sure, you can paint over top, that is ok. Just make sure you left enough time for it to dry, as Zinsser Bulls Eye 1-2-3 is waterbased. I would recommend 2 coats painting. After first coat leave it to dry 30 mins.
It is formulated to seal, prime and block out stains on previously painted or new work. Any oil or latex paint can be applied over it.
In most cases only one coat is necessary to prime most surfaces. If excessive absorption occurs over very porous substrates a second coat may be necessary. Spot priming is recommended only under high-hiding topcoat finishes. For best results, prime entire surface before painting.
Any oil or latex paint can be applied over it. Use it on all interior and exterior surfaces.
Zinsser 123 is great for surfaces that are easier to adhere to and has low odour. Zinsser Cover Stain provides durability and adhesion on glossy glossy surfaces. It's especially good on raw wood or MDF removing the risk of swelling that you could get with the water based 123 primer.
Bulls Eye® 1-2-3 effectively primes and seals a wide variety of interior and exterior surfaces. A 'bond coat' primer that's great for hard-to-stick surfaces, it offers excellent adhesion without sanding.
Zinsser® BULLS EYE 1-2-3® is a whole house, Universal interior/exterior, water-based stain-killing primer-sealer. KILZ ADHESION primer is a water-base, modified-acrylic primer specifically formulated to bond to a variety of 'tough-to-paint' surfaces.
In most cases only one coat is necessary to prime most surfaces. If excessive absorption occurs over very porous substrates a second coat may be necessary. Spot priming is recommended only under high-hiding topcoat finishes. For best results, prime entire surface before painting.
You will want to use 2-3 coats of primer to ensure there is a good bond between the new paint and the wall, and also to cover up any previous colors, especially if they are red, orange, or a strange outdated color. In short, you will typically need 2 coats of primer for most painting projects.
A good rule of thumb is to wait at least three hours to recoat your paint or primer if it's water-based. Waiting 24 hours is best for oil-based paint and primer. If you're unsure, the instructions on the paint's label can give you the best final say.
Shellac primer
You can paint after 1 hour if you want, but we suggest letting it sit for at least 2 or 3 hours or overnight to be sure it's completely dry before painting.
Paint peeling only usually happens when you're trying to paint over an unprimed or poorly primed surface. For those who aren't sure, give yourself a primer drying time of at least 1 hour, or simply leave your model in a dry and clean place overnight.
Most latex primers dry to the touch in 30 minutes to one hour. But for best results, don't paint until the primer completely dries—which can take up to 3 hours, depending on temperature and humidity. Once the primer is completely dry, it's prime time for painting.
Any oil or latex finish paint can be applied over Zinsser Bulls Eye 1-2-3. Adheres to slick materials - gloss paint, tiles, metal, hardboard, melamine, plastic, GRP, uPVC. (but NOT Varnish or clear polyurethane finishes - instead use Fossa Block & Bond for these internal surfaces).
Zinsser primer exhibits improved adhesion on tougher surfaces compared to Kilz primer, ensuring durable coatings all the time. As long as the surface is clean, Zinsser will stick to it even without sanding.
Do I need to sand back to bare timber? No, you just need to prepare and prime them with a high-quality undercoat. Zinsser Cover Stain uses an advanced oil-based formula which cuts drying time, covers most stains, and adheres to most surfaces.
Dry Time– In most cases B-I-N® will dry to the touch in 20 minutes and can be recoated in 45 minutes. The dry primer film develops full adhesion after it cures in 1 to 3 days. Lower temperatures, higher humidity and the addition of tint will prolong dry and cure time.
Zinsser Cover Stain has a 2-hour recoat, meaning you can easily paint over it on the same day, even with water-based paint like emulsion.
Since primer's function is mainly to bond and cover porous surfaces, it is not made to withstand elements like paint. Because of this, if you leave primer without a top coat (or paint) it will deteriorate and break down, probably in a chalk like form.