A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
Give the shock a good 12 to 24 hours to work it's magic. If the algae hasn't cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.
It all depends on the type of pool and the chemical levels in the pool. Your pool can keep running for a few days with no problems while without a pump. However, know that a standard pool needs a pool running for at least once in 24 hours, or you might notice an algae bloom.
Answer: After shocking the pool, it will need filtration and circulation. Run the pump as much as possible. Keep the filter clean (daily) until the water runs clear. Be sure to brush the pool often during this process as above-ground pools do not have drains at the bottom.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
Best Time to Shock Your Pool
The best time of day to shock pool is when the sun is down. So, experts recommend shocking your pool in the evening or at night, to make sure it does its job. Shocking during the day can be ineffective as UV rays from direct sunlight significantly reduce free chlorine levels.
Never close the cover immediately after shocking the pool. It is recommended to wait several hours before closing the cover. Use a test kit to regularly test the pool water. If the tests results are good, this does not imply the water chemistry was good prior to your current test results.
Apply the shock at night time, as sunlight burns up chlorine and greatly reduces its effectiveness. Run your pump (at night) for at least 8 hours to ensure good distribution.
The best time of day to shock your pool is in the evening. This is because the sun's rays can affect the effectiveness of the chlorine by dissolving it too quickly, before it has a chance to rid the pool of contaminants and clean the water.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Shocking your pool isn't necessary, although, it's not a bad idea either. If you get an extremely heavy rain fall, you could shock your pool for good measure. This will help fight off any contaminants that the rain may have brought to your pool.
It's often recommended to shock your pool once a week. If you don't do it every week, you should at least do it every other week. This is necessary to maintain your pool's water chemistry. If you have a lot of people over in your pool or have a party, you may want to shock your pool more frequently.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
In the industry it is recognized to have the pool run for 3 hours at a bare minimum up to 24 hours. 24 hours really is overkill but it'll ensure the water is completely mixed with the chemicals.
Is It Safe To Run The pool Pump With The Pool Cover On? It is safe to run the pool pump and filter with a swimming pool cover on. The pool cover doesn't in any way stop or hinder the pool pump from circulating the water or carrying out its function.
Maintaining chlorine levels of 10ppm or higher for extended periods of time can not only ruin your liner and cover but also severely damage your pool equipment. Chlorine should be maintained ideally between 1.5ppm to 3ppm.
You want some clear area between the edge of the pool and the cover to pour chemicals. You don't need to remove the cover, you just need enough room so you aren't splashing any full strength chemicals on the cover. When you are done with the chemical addition you can pull the cover back into place.
And how long do you have to wait before you can swim? You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool.
The treatment used in shocking pool is highly corrosive. Will cause skin and eye damage. May be fatal if swallowed. If this treatment gets in your eyes: Hold eye open and rinse slowly and gently with water for 15-20 minutes.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool's size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool's turnover rate is.
How Long Should I Run My Pool Pump For? Ideally, you should run your pump for 24 hours a day, but we know that's unrealistic (and pricey), so let's look for an answer that keeps your pool clean and your wallet full. Generally running your pool pump for 12-hours a day is a good option.
Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. A proactive, productive and energy-saving maintenance activity is to remove the debris floating on the pool surface with a hand-held skimmer.