Several gentle pumps will usually work better than a couple of hard pushes. If your clog is going to come out, it should happen in less than 10 minutes. If not, it's time to move on to a snake or call a plumber.
Wait about 10-15 minutes before trying to unclog the toilet, as some water might drain on its own. Squeeze a lot of liquid dish soap, about one cup, or pieces of bar soap into the toilet bowl.
Is it okay to leave a clogged toilet overnight? In most cases, you can leave a clogged toilet overnight. However, calling an emergency plumber near you might be warranted if water starts leaking from the pipes. A simple clog likely won't cause this, but an inexperienced homeowner messing with the plumbing could.
If you can't unclog the toilet using a plunger or a snake, your next best option is to use boiling water. Boiling water can help to dissolve the clog and free up the pipes.
You may just be using it incorrectly. Do this: Next time you have a clog, use your plunger like this: Ensure the flange lip is unfolded. Get a good seal on the toilet drain (that is, make sure you're covering the entire drain or you won't have enough pressure to loosen the clog.)
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
How to Unclog a Toilet With a Plunger. After the water is turned off, try using a conventional plunger to unclog the toilet. Be sure the water covers the cup of the plunger; if it doesn't, you may need to manually control the flapper until enough water enters the bowl.
For preventive drain cleaning, you can use Drano® Max Build-Up Remover in drains, toilets and even septic systems. Apply Drano® Max Build-Up Remover overnight or before you go to work, then wait 6 to 8 hours before running warm (not hot) water down treated drains or flushing treated toilets.
If your toilet is backing up, it may be due to your tank not having enough water to flush it. Low tank water levels may result from several causes. Damaged water supply lines, broken tank seals, and other issues may prevent tanks from filling completely. Some toilet models may also have low flush strength.
Check water level in toilet bowl
Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
Attempting to force a clog through a toilet with a plunger can often make the problem worse. Instead, create a seal and slowly push down on the plunger before pulling it back sharply. The suction can help pull the clog back up toward the bowl, breaking the blockage and allowing gravity to take over.
How to Tell if Your Toilet is Clogged. Signs that your toilet (or sewer line) is blocked include: The water does not flush properly, stays in the bowl for long periods or ends up overflowing over the top of the bowl. When the toilet is flushed, water starts to gurgle up in your shower or bathtub drain.
Drano® Liquid Drain Cleaner starts working to unclog your drain on contact. After 15 to 30 minutes, clogs are substantially minimized or dissolved. A final blast of hot water flushes away what's left of the clog.
When Drano is left in the drain for too long, it can cause corrosion of the pipes. The chemicals in the product are designed to break own the clog, but if left for too long, they can start to break down the pipes themselves.
It is Extremely Corrosive For Your Drains
When your pipes are clogged, Drano will sit on top of the clog, continually reacting and generating heat until the clog dissolves. This can put a great deal of stress on your drains as the heat can cause PVC pipes to soften and even break or collapse.
There is only one Drano® product recommended for use in slow-running toilets: Drano® Max Build-Up Remover. It contains microorganisms that break down organic matter in pipes that can slow water flow. (However, it will not open a completely clogged toilet.
When you are using a baking soda and vinegar solution to clean out your drain, you are actually causing the rubber and plastic that are used for the drain's pipes to be eaten away by the mixture. Over time, this rubber and plastic will break down, causing the drain to become even more blocked.
If more than one drain is slow moving, gurgling, smells bad or has water backing up, you most likely have a main sewer clog.
High Water Pressure with Baking Soda and Vinegar
To do this, use a 2:1 ratio of vinegar to baking soda, and mix it into 60 gallons of water. As you pour the water down the drain, use a drain snake or plunger to dislodge debris that is blocking water flow.
Drano is not only ineffective, but it's also extremely damaging to your plumbing system. The heat created by the chemical reaction is more than your drains are designed to take. Corroded, aging plumbing can easily breakdown. Pipes can split and the glue holding them together can disintegrate.