When Is It Safe To Swim After Adding Cyanuric Acid? As a general rule though, you can swim in your pool within 20 minutes of adding cyanuric acid. Make sure you have the pump on when you add it so that it mixes in the water. It's always best to check the manufacturer's instructions though.
Should I use cyanuric acid? – No. It should never be used in indoor swimming pools, spas or hot tubs. Remember that CYA is intended to reduce the loss of free chlorine caused by the sun's ultraviolet rays.
When the product reaches the filter, there may be a temporary increase in filter pressure which will dissipate as the product dissolves. You may swim immediately if Stabilizer was added through the skimmer, otherwise wait 12 hours to swim until all product in the pool is dissolved.
CYA is not consumed the way that chlorine is consumed. When adding pure CYA into a T-shirt in my skimmer, it dissolves completely over a day and registers fully in my pool within 2 days.
Saltwater pool manufacturers recommend maintaining cyanuric acid levels around 60-80 ppm. This is a bit higher than the 30-50 ppm range recommended for non-saltwater pools. And if you live in an area where your pool gets a lot of direct sunlight, you may even consider bumping your cyanuric acid up to 80-100 ppm.
And stabilized chlorine (like dichlor or trichlor) already comes with CYA, so you'll likely be adding it to your pool water throughout the season. Because CYA is an acid, you'll need to handle it carefully. It can damage your filter and your pool, especially if you have a vinyl liner.
We recommend adding Acid weekly! Adding a little and often is better for your water and can actually save you money overtime. Large doses over longer periods of time take a larger portion of your 'Total alkalinity' away.
The half-life of chlorine—when exposed to direct sunlight—is about 45 minutes. That means half your chlorine is gone in 45 minutes. Another 45 minutes, another half of your chlorine is gone.
The effects of high cyanuric acid aren't a concern for your health particularly. The main issue when cyanuric acid is too high is chlorine becomes less effective. The higher the levels of cyanuric acid, the more free chlorine is needed to maintain the same level of protection.
Answer: Cyanuric acid shouldn't be at Zero for an outdoor swimming pool because chlorine will deplete faster in hot and humid weather, leading to cloudy water. If your FC is at normal level of 3ppm, raise Cyanuric acid level to 40 ppm and you will reduce chloramine levels that make your water appear cloudy.
Cyanuric Acid (CYA) is a pool balancing product used to help chlorine last longer. Chlorine, in its natural form, is unstabilized—which means it degrades when exposed to sunlight. Adding Cyanuric Acid reduces the sun's impact on chlorine loss.
We also found that cyanuric acid is denser than water so it sinks to the bottom of a body of water.
Cyanuric acid is raised by adding chlorine stabilizer containing cyanuric acid. The only way to lower cyanuric acid is by replacing water.
All alkaline materials are buffers. Cyanuric acid happens to be the most common buffer found in pool water. In effect, cyanuric acid helps stabilize both chlorine and pH. It binds with chlorine to prevent photolysis and it keeps pH elevated.
Why You Have Low Cyanuric Acid
The most likely reason is that you've only ever used unstabilized chlorine in your pool. Heads up: Unstabilized chlorine, such as sodium hypochlorite (liquid chlorine), lithium hypochlorite, and calcium hypochlorite, is pure chlorine.
If there is a problem with the chlorine, pH or other chemical levels in your pool, adjusting those levels can be enough to correct the cloudiness. For example, if your pool water is too basic, you can add hydrochloric acid or sodium hydrogen sulfate to lower the pH.
It's best to run your pool pump during the day
Not only does sunlight give fuel for algae to grow, it also destroys your pool chlorine and this is why you should always run your pool during the day!
Chlorine raises the pH level; to counteract this, muriatic acid is used to lower it again. If you use too much muriatic acid, however, the levels can dip dangerously low, which can cause rashes and eye irritation for swimmers and damage metal parts of your pool equipment.
The main reason for high CYA levels in your pool is from using too much stabilized chlorine. When the pool water evaporates, CYA remains in the water, much like other chemicals such as salt and calcium. As an example, 1 lb. of trichlor in a 10,000 gallon pool will raise the CYA level by 6 ppm.
Is Having Low Cyanuric Acid a Problem? Chlorine is actually more effective at killing the bad bugs when pool stabilizer is low. The problem with low cyanuric acid is chlorine degrades quickly in the presence of sunlight. Chlorine is rendered completely ineffective within a few hours of sun exposure.
The problem is that cyanuric acid does not dissipate or evaporate but instead lingers and gathers in the pool water. Over time, the pool technician would be required to constantly re-apply Tri-Chlor or Di-Chlor products to re-sanitize the pool.
Shock does not contain any cyanuric acid, so after 24 hours, the elevated amounts of chlorine are no longer in the pool. as 90 percent of the chlorine in the water in two hours.
Clorox has absolutely NO Cyanuric Acid (CYA) in it nor does it increase CYA at all when you use it. You should show them. It's mostly water, then sodium hypochlorite (i.e. chlorine), and sodium chloride salt, and then a small amount of sodium hydroxide and a very small amount of sodium polyacrylate.
For the most part, yes. It can be unattractive and it should be addressed, but it is mostly safe to swim in cloudy water. The only exception would be if the pool is cloudy because there are too many chemicals in it. This pool water would be unsafe to swim in and should be avoided.