To reset a furnace blower motor, turn off power to the furnace using the emergency switch or the circuit breaker. Wait 2-3 minutes, then locate the red or yellow reset button typically found on the blower motor housing. Press it firmly, and restore power.
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
Diagnosing a faulty blower motor versus a bad resistor typically comes down to what fan speeds are working. If the fan only works on the highest setting, the resistor is usually the culprit. If the fan doesn't work on any speed, or if it makes strange noises, the motor itself is likely failing.
If your furnace fan won't turn on, first check your thermostat to ensure it’s set to "Heat" and the fan mode is on "Auto." Next, verify that the furnace is receiving power by checking the circuit breaker and ensuring the safety door panel is tightly closed.
Resetting a blower motor typically involves cycling the power, checking for tripped thermal switches, or adjusting your thermostat. These methods apply to residential HVAC systems, though the exact steps vary depending on whether you are working on a furnace, an AC unit, or a car's blower motor.
A bad furnace blower motor usually causes weak airflow, strange noises (screaking or grinding), overheating, or completely failing to turn on. The quickest way to check if it's dead is to inspect if the fan wheel spins freely by hand or if it has seized.
To reset a furnace, lower your thermostat to the lowest setting. Turn off power using the furnace's emergency switch or circuit breaker. Wait 2-5 minutes, turn the power back on, and adjust your thermostat. If the furnace locked out due to a safety issue, you may need to press the reset button.
An intermittently failing blower motor is usually caused by an overheating thermal overload, a failing start capacitor, a faulty control board, or a worn-out ECM control module. The motor will often shut down to prevent permanent damage and then restart after it has had time to cool off.
A furnace blower motor is the heart of your heating system. It's the part that pushes warm air from your furnace through the ducts and into your rooms. Without a working blower motor, your furnace might create heat, but that heat would stay trapped inside the unit.
To put it very simply, the furnace fan limit switch is a control that tells your furnace's fan when to turn on and off. So, when the furnace isn't on, it tells the blower not to operate (and send cold air into your home) and when the furnace is on, it tells the blower to turn on and start circulating the warm air.
Replacing a blower motor resistor typically costs between $90 and $300 for parts and labor. The part alone runs about $20 to $100, while labor takes a mechanic 30 to 90 minutes, adding another $50 to $200 depending on your vehicle's make and model.
The blower motor resistor can be removed after the bolts have been removed. The wire should be linked to the blower motor's positive terminal, and the negative terminal should be attached to the blower motor's negative terminal. This will turn off the resistor and allow the blower motor to run at full speed.
A bad blower motor relay will typically cause your HVAC system to produce no airflow, blow warm air only, or leave the fan running constantly. It often fails due to overheated electrical contacts or melted wiring.
To reset your furnace, start by turning off the circuit breaker and furnace power, wait about 30 seconds to a minute, then turn the power back on. If your furnace uses gas, you may also need to turn off the gas for a few minutes before turning it back on.
The heat exchanger is often considered the most costly part of a furnace to repair or replace. It is a critical component that transfers heat from the combustion process to the air that circulates throughout your home. Over time, heat exchangers can crack due to the constant heating and cooling cycles they undergo.
Furnace blower motors typically last 10 to 20 years (averaging around 15). However, their exact lifespan depends heavily on regular maintenance, filter changes, and usage patterns.
Most furnaces have a reset button near the blower compartment itself, though the exact location may vary depending on the make and model. It's usually red or yellow and small in size. Consult your furnace manual for guidance if you're unsure where it is.
Replacing a furnace blower motor typically costs between $400 and $1,800, with the national average landing around $600 to $800 for parts and labor. Your total bill will depend heavily on whether you have a standard single-speed motor or a high-efficiency variable-speed motor.
Short cycling
This is one of the most common furnace problems, and it can stress important furnace components such as the blower motor, limit switch, or flame sensor. There are several potential causes of short cycling, including some that are related to your furnace's built-in safety systems.
Knowing the common causes of blower motor failure and how to fix them can save much time and money.
A blown blower motor fuse breaks the circuit, stopping your fan. Symptoms include dead airflow or an unresponsive climate switch. To verify, locate your fuse box (usually under the hood or near the steering column), pull the fuse labeled for the A/C or blower motor, and check it.
In newer applications, the blower motor resistor is actually a solid state module that sends a varied signal to the blower motor. The traditional blower motor resistor is connected to ground and wired in series with the blower motor assembly.
To reset a furnace blower motor, turn off power to the furnace using the emergency switch or the circuit breaker. Wait 2-3 minutes, then locate the red or yellow reset button typically found on the blower motor housing. Press it firmly, and restore power.
Yes, unplugging or turning off power to your furnace at the breaker can act as a reset for certain systems, especially gas furnaces with electronic control boards. However, this only resets the system temporarily and does not fix underlying issues like ignition failure, airflow problems, or faulty sensors.
After pressing the button, give the unit a few seconds to reset and begin running again. If the furnace doesn't start up after pressing the reset button, you can try pressing it one more time. However, if the furnace turns on and then shuts off again, we do not recommend pressing the reset button repeatedly.