To reset mechanical thermostats, simply turn off the thermostat and flip the circuit breaker. This can be done by going to the breaker panel and turning off the appropriate breaker switch for 30 seconds. After turning the breaker back on, turn the thermostat back on and the thermostat should be reset.
If your boiler stops responding to your thermostat or heating controls, it's worth checking the batteries. Not all thermostats use batteries - some are wired into the mains but have backup batteries in case your power fails. If you've experienced a power cut, your thermostat's backup battery might've run out.
Redo the Thermostat Wiring
Other times, corrosion and lint can build up on the wiring and prevent the current from passing through. If either of these is the case, call an HVAC technician to inspect and redo your thermostat's wiring. They have the knowledge to get the issue fixed!
First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious, as the housing may be hot.
If your thermostat has fresh batteries but suddenly lacks power, flashes, or isn't responsive to adjustments, it may need replacement. If resetting the thermostat doesn't resolve the problem, you may have wiring problems or faulty components causing your thermostat to not turn on.
If your furnace turns on but no heat is produced, there may be a problem with the fuel supply or the ignition system. If something is stopping your furnace from receiving gas, there is no fuel to combust so the furnace will not create any heat. The furnace turns on but no heat comes out.
Turn off your air conditioning system. Locate the reset button on the thermostat's circuit board. Use a soft bristle brush to gently remove any dust or debris that may have accumulated on the thermostat components. Press and hold the reset button for 5-10 seconds until the display goes blank.
One of the most common issues with a heating system not functioning is dirty air filters. If your air filters are extremely dirty, then the airflow can be blocked. Check for clean air filters, vents, and registers. Make sure there are no rugs or furniture blocking vents or registers as well.
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete.
The Thermostat Needs New Batteries
If the batteries are dead, the thermostat may say the heat is on, but the furnace isn't running. Look for a low battery warning light; some units beep if the battery is low. Replacing the battery should fix the problem. To avoid issues, replace the battery seasonally.
To reset a non-programmable digital thermostat, you'll need to take the face-off and hold the reset button for five seconds. You can also try removing the batteries for five seconds. Both of these methods should result in a reset thermostat.
Your house may not be heating up due to several reasons: a malfunctioning thermostat, issues with your heating system, blocked air filters, or inadequate insulation. It's important to check these components to identify and resolve the problem.
Turn your thermostat “off”, then flip the related circuit breaker “off”. Wait 30 seconds, then turn the breaker back “on,” then the thermostat. Set the thermostat to hot or cold, whichever you prefer, and your desired temperature. This should effectively reset it.
The cause of your furnace not blowing hot air could be the thermostat configuration, a dirty air filter, the high limit switch, a clogged condensate line, insufficient fuel, leaky ducts, ignition problems, a blocked burner, flame sensor issues, gas valve malfunctions, a cracked heat exchanger, or a clogged coil.
Some of the most common thermostat issues include:
The thermostat is broken, not properly level, or dusty. The thermostat needs to be recalibrated. There is loose wiring causing a thermostat issue. The thermostat is not in an ideal location in your home.
Radiators might not be getting hot due to trapped air requiring bleeding, a malfunctioning boiler or central heating pump, thermostatic radiator valves that might be stuck or set too low, or the central heating system having sludge or rust which causes blockages.
If ductwork is not configured correctly, and the system is sized incorrectly, your home may still be cold even when the heating is on. With ductless system, there are no air leaks through ductwork. If properly sized, ductless is usually more efficient than traditional systems.
If you've been cranking the thermostat up and down, but failing to achieve a comfortable temperature, you may need to reset the thermostat for your heating and cooling system.
If your thermostat is fully functional and you're still unable to feel any heat coming from the vents, you may be dealing with some of these problems: Dirty evaporator coils. Clogged pipes. Full air filters.
In most newer systems, the button is often directly next to the blower motor, while in older systems, it may be harder to spot as it is sometimes underneath or behind the motor. The reset button is often made of yellow or red plastic and marked with a large “R ” to make it easier to spot.
If your furnace is blowing hot but your home is still cold, it may be a problem with your ductwork. You may have leaky or damaged ducts that are letting hot air escape and cold air in. Sometimes a damper in the system can get miss-adjusted or come loose, thereby inadvertently blocking or reducing airflow.