The first option you can try is an ammonia-free cleaner like Windex. Spray a two-foot section of your floor and let the cleaner sit for about two minutes. Next, use a dish-scrubbing sponge to rub the section of the floor where you sprayed the cleaner.
Finally, when used and applied the right way, Pine Sol doesn't leave behind any residue that will leave you with an unsightly hardwood floor surface. Wax and oil-based cleaners, on the other hand, leave behind a hazy residual substance.
You're Using Too Much Product
If you're sure you've got the right product, but your floors still end up sticky, there might be another issue. Namely, it's important to properly dilute the cleaning agent with water. Otherwise, it will leave a sticky residue that's going to be even harder to clean.
A: Yes. Usually no rinsing required. On wood surfaces, do not allow puddles of cleaner to remain.
Yes, but you need to make sure it's adequately diluted and rinse your floors afterward. Failure to do so will likely result in a product buildup on your floors. So, if you love the scent of Pine-Sol or that's all you have on hand, you'll be perfectly safe mopping your hardwoods with it.
According to Pine-Sol, you should refrain from using undiluted Pine-Sol on metal surfaces, such as copper or aluminum.
What is this? Pine-Sol is more acidic than Fabuloso, which gives it an advantage in breaking down stubborn stains and complex messes caused by grease. Pine-Sol Original is the only liquid cleaning solution that disinfects.
“Fill up the sink with hot water & a cap full of your favorite Pine Sol floor cleaner. Add 2 tbsp of vinegar & use to clean any type of floor. I use this method on my hardwood floors to get a clean, smooth & shiny surface!”
First of all, the only hazardous ingredient listed on the Pine Sol MSDS is alkyl alcohol ethoxylates. These belong to a group of chemicals called "aromatic hydrocarbons" which are petrochemicals with strong, pungent, odors. The only health hazard listed on the MSDS is that it is an irritant.
Some of the problems that can be caused by inhaling Pine SOL
However, the most common health problems are listed below: Irritation of the mucous membrane. Nausea and headache. Loss of consciousness.
To get the best results, stand on the towel and move your feet back and forth until you've dried the entire floor. If the residue is still there after mopping with vinegar, add a drop of dishwashing soap to a non-abrasive sponge and scrub the floor. Rinse the sponge and reapply the soap as often as needed.
If the sticky floor is due to an accumulation of moisture and tracked-in dirt, start by soaking a wet mop in warm water then wring it out until it is just slightly wet. Alternately, you may soak old floor rags in warm water and run over the floor surface.
But if your wood floor is in a high-traffic area, such as a kitchen, it may sometimes require a more concerted cleaning effort. Pine-Sol is an effective cleaner as well as a deodorizer and disinfectant that has been around since 1929, and is suitable for wood if used properly.
A: Yes. Original Pine-Sol® Multi-Surface Cleaner is registered with the EPA as a disinfectant when used as directed full strength. When used according to the instructions on the product, it kills 99.9% of germs and household bacteria on hard, nonporous surfaces.
It is preferable to use cold water instead of hot water when mopping. The reason is that it does not damage the flooring and it retains floor shine. It also helps in eradicating germs and bacteria. Additionally, cold water saves a lot of electricity and leaves off a cooling effect later after cleaning.
They found the presence of this type of formaldehyde in popular brands Comet, Pine-Sol and Simple Green, among many others. The Organic Consumers Association recently published their review of the toxic chemicals in household cleaning supplies and the common health issues they cause.
A new study out today reveals that numerous popular cleaner brands, including Glade, Clorox, Pine Sol, and the ostensibly eco-friendly Simple Green, contain chemicals that are known to cause hormone disruption, pregnancy complications, birth defects, and cancer, and can aggravate allergies.
Or for everyday mess control, keep the Pine-Sol® mixture in a spray bottle for quick cleaning spritzes. Scrub crevices in counters with grout with an old toothbrush. Scrub stubborn messes or stains with full strength Pine-Sol®, using plastic scrubbing pad or cloth. Finish by rinsing with water.
According to its FAQs page, Pine-Sol doesn't recommend mixing its products with any other household cleaners. The proper way to use Pine-Sol is to mix ¼ cup per gallon of warm water.
Add ½ cup of Original Pine-Sol® along with your regular detergent to boost a load of white or colorfast laundry.
Pine-Sol: If you mix bleach and Pine-Sol in large amounts, it will create chlorine gas.
Lysol can be hard to find online and in-stores, but Pine-Sol seems to still be available at most retailers. Compared to Lysol, Pine-Sol has a longer contact time (Lysol's ranges from 2 minutes to 5 minutes) but will still effectively help you to limit your contact with the virus.
Pine-Sol vs Lysol
Lysol works just like Pine-Sol and will get rid of bacteria, fungi, mold, viruses, etc. after getting into contact with the surface for at least ten minutes. However, it may not be as effective if there are organic materials.
You can use Pine-Sol® cleaners on hard, nonporous surfaces, including floors, sinks, counters, stoves, bathtubs, shower stalls, tile and more!