Insert a stiff putty knife in the gap between a pair of tiles, wedge it under one of the tiles and pry, exerting light to moderate pressure. If the tile doesn't come off, don't force it. You may be able to weaken the glue bond with heat.
Removing a 4-inch granite backsplash to make way for a new backsplash material, or none at all, is a lot easier than you might suspect. A word of warning, though: It will be next to impossible to avoid damaging the wall, so be prepared to make drywall repairs.
Tap the end of the nail set with a hammer to shatter the tile and pry the pieces off with a chisel. Move the nail set to several areas on the surface of the tile and continue to shatter and chisel away the pieces until you remove the majority of the tile.
So, for removing the Quartz countertop without damaging it, loosening surrounding adhesive is extremely important. To make this easy, use a caulk softener and allow it to stand for an hour. Remove the adhesive from the wall or backsplash with the help of a putty knife.
Granite backsplash sits on top of the counter and is attached to the wall with silicone. A thin line of clear caulk is used to seal the right angles where the backsplash meets and wall and where it meets the counters so that no crumbs or dust gets stuck in small spaces.
Using a taping knife apply the joint compound in a diagonal down then back up motion, applying a thing layer of joint compound. Cover the entire area, ensuring a smooth, even coverage. (TIP: Apply drywall mesh to the wall prior to applying the Spackle or joint compound. This helps create a smoother finish.)
Removing the kitchen tile backsplash is all about technique, precision and patience. Without all three, you'll spend hours repairing your poor drywall, so be prepared to take your time and follow the steps carefully.
sure it can.. you might break a few pieces thou.. first it helps to use a sharp knife or razor blade to cut the mesh around any pieces you want to remove.. then get yourself a chisel and hammer and gently try to chisel and pry each piece off.. you might find that some pieces come off fairly easily..
Use a ball peen or masonry hammer and cold chisel to tap the pieces free. Always wear safety glasses when removing ceramic tile. In some cases, the only way to tear out the ceramic tile is with heavy equipment such as a jackhammer or air chisel.
Without disturbing the surrounding wall or floor installation, you can easily replace one or a few tiles that have chipped, cracked, or broken. Here's a way to replace damaged ceramic tile. Remove the grout with a grout saw. Crack the tile with a hammer and cold chisel.
Dig out the mortar between the bricks to loosen them and help them come away from the wall easier. Dig the joining chisel into the joints and tap it with the hammer to break up and remove the mortar. Work from top to bottom and from left to right to get the old mortar loose.
While you might want a backsplash to match your counter (and there are many custom, lovely ways to do that), don't be tempted to tile above a 4” granite, or stone, slab backsplash. Instead, before you tile that area, take the 4” slab backsplash off. Why? Because, typically, you only have 18” of height there.
Can you remove or replace a granite countertop without damaging the cabinets? Of course you can! Granite countertops are a favorite for many homeowners because of their beauty and durability. Granite is a tough material, but it still needs to be cared for.
Tapping a wooden shim between the countertop and the cabinet's edge will help to hold the granite countertop at the desired spot. Continue screwing and shimming from the front side of the cabinet until you can slowly lift the entire front frame.
You can also insert a reciprocating saw with a long flat blade between the granite and wood top to detach the granite from the wood where they are glued together. You can also use a hammer to break up the countertop in place and remove it in pieces if you don't plan on saving or reusing it.
Adhesive for Granite Countertops
Epoxy glue is the most commonly used type for granite countertop installation. It's strong enough to attach the granite to cabinets and to hold two pieces of stone together. You need something just as strong as the stone itself, and epoxy fits the bill.
Tiling over granite is no problem at all - not a bad surface to tile to.