If you make sure to properly seal your pavers, then generally all you'll need to do to keep them looking great is to give them a regular rinse with the garden hose. And, as a bonus, the sheen of a good sealant can make pavers that have been around for years look like new again.
The basic rule of thumb is every 3-5 years. For film-forming sealants, you will be able to notice when the physical barrier is showing signs of wear. For non-film-forming sealants, you will begin to see a significant color change of pavers during a rain when the sealant is wearing thin.
Once a concrete paver is sealed, DIY upkeep is pretty simple. Generally, interior pavers that have been grouted and sealed just need to be swept, mopped, and spot-cleaned as needed with a gentle, non-acidic multipurpose cleaning solution, such as Enviro Klean All Surface Cleaner or Light Duty Concrete Cleaner.
Yes, you can pressure wash your pavers. But while using a pressure washer at a basic level is simple, ignorant and inexperienced users can easily damage their pavers by using a stream that's too powerful, by holding the wand too close to the pavers, or by falling into any number of other rookie mistakes.
You need 48 hours of dry weather after your sealer has been applied to cure it. (Remember to turn off your automatic water sprinklers.) If the sealer is not cured correctly, water can cause white marks or stains on your pavers and can even be trapped beneath the layer of sealer.
Pavers should be cleaned and sealed every two to three years depending on how often they are exposed to traffic, liquids, sunlight etc. Paver surfaces can also be power washed between cleanings but paver sealing is still necessary after paver cleaning has occurred.
After you have invested in pavers, whether that be a patio, poolside deck, etc., it is important to seal your pavers in order to protect from the weathering UV rays. These rays, which are known to impact the skin negatively, also impact the surface of your pavers negatively.
Pavers should be resealed every 3 to 4 years on average. You will know when your pavers need to be resealed because water will stop beading on the surface and the sheen will diminish. In addition, you may notice weeds starting to grow in between joints and the pavers may start to lose their color.
Blotchy and Dark Concrete: Blotchy concrete can result from over application. In order to prevent over application, apply sealers in thin, even coats. If over application does occur, use Xylene to correct the problem.
Acrylics. Acrylic paver sealers, either solvent- or water-based, offer the most comprehensive ultraviolet (UV) resistance. Acrylic sealants can be breathable, depending on their solid content.
Using a nap roller for sealer application will take several times longer than using a paver sealer sprayer and joint stabilization is difficult to achieve. Spraying is the preferred method of applying water based paver sealers as it allows enough sealer to get into the joints.
How Much Does It Cost to Clean and Reseal Pavers per Square Foot? In total, you should expect to pay around $2 per square foot to clean and seal pavers. The price may vary between $1 and $3 per square foot, depending on the sealant and method of cleaning.
Fall or spring is a great time of the year to seal pavers. Cooler weather allows the sealer to penetrate into the pavers unhindered.
Sealers make bricks shine. Last, but not least is the sheen. Our sealers that we use at Paver Protectors offer a nice sheen and most companies have additional sheens available as do we. Our water-based sealers that enhance the color, they also enhance the sheen.
You pressure clean the pavers, re-sand the paver joints and then apply two coats of your favorite paver sealer and the job was complete.
Seal pavers during cooler hours of the day, so think morning and evening, when the sun is still up but is the farthest away. The ideal temperature is between 50-90℉ degrees. A paver sealer applied to a surface that is more than 100℉ will only cause it to burn up and not provide any long-term benefits.
Never Too Late to Seal Pavers
It's always best to seal soon after a new installation. But, our proven system of repairing, cleaning and sealing will also bring back the original luster to old, dirty and fading pavers. Sealing is the final step in a comprehensive process.
Most contractors and manufacturers recommend sealing pavers for the many benefits. Both concrete and brick pavers are porous materials that can change quality and appearance when they absorb liquids.
Then, about 24 hours prior to sealant application, thoroughly cleanse pavers of any remaining residue with Techniseal's Paver Prep, a powerful efflorescence cleaner that will give you a nice clean surface on which to work. Our paver preparator also maximizes sealant penetration and adherence.
One of the best paver sealers is the Siloxa-Tek 8500. It is a penetrating concrete sealer designed to treat a variety of applications with an emphasis on hydrophobicity and reduction of water uptake. It dries completely clear with a natural finish that will not change the look or appearance of the susbtrate.
The pressure washer in combination with a dirt cutter is an excellent option. This removes not only weeds and moss from the surface, but also from indentations. Keeping up with this type of cleaning means that there is less time for weeds to grow. It also helps to maintain the beauty of the paving stones' surface.
The easiest test is by letting water sit on your pavers for about 20 minutes. If the water beads up on the surface and does not leave a stain, your sealant is still working, if it sinks into the paver, however, then a fresh coat of sealer is likely required.
A sealer can make or break your paver patio. It does not only help increase the lifespan of your pavers, but it also helps maintain their rich colors. While a good sealer can last for decades, you may need to reapply it once it begins to fade.