You'll know the blockage is gone if your toilet makes a suction sound when flushed and the water drains normally. You can try this method a few times in a row for stubborn clogs, but if it doesn't help unclog the blockage, try our last tip for getting rid of a clog.
Check water level in toilet bowl
After plunging for thirty seconds, quickly break the seal and remove the plunger. Listen for a gurgling sound from the drain (a good sign) and check the water level in the toilet bowl. If nearly all the water drained from the bowl, then you've probably cleared the clog.
Start by slowly and firmly pushing down to create a seal and then pulling up sharply to dislodge the obstruction. When you pick up the pace, you will notice the water starting to drain. It usually takes at least 15 minutes to unclog a toilet. When draining, some water may dislodge and push forward the blockage.
Will a toilet eventually unclog itself? It sure would be nice, but it's fairly rare for a toilet's clog to clear up after a few hours. It can happen, but only in select circumstances. Here's what you need to know about whether your toilet will unclog itself.
A fully clogged toilet won't move waste down the drain at all. If it's running slowly, it's a partial clog that does let water through, but not as fast as it's supposed to be.
Stop Flushing!
If your toilet doesn't flush properly the first time, the last thing you want to do is try flushing again. The clog will prevent the water from going down the drain, meaning it will overflow the toilet and get all over the floor. This can create a much bigger (and must smellier) mess.
Caustic soda is a nasty chemical that can burn, but it's very effective for unclogging toilets. To use this chemical, you need to get some rubber gloves and eye protection. You can pick the chemical from the local hardware or grocery stores. Pour a ¾ gallon of cold water into a bucket, and add 3 cups of caustic soda.
Then pull up sharply to disturb the clog and loosen it. Continue vigorously pushing and pulling until the water begins to drain. It may take 15 to 20 cycles before the toilet unclogs. Be patient.
One of the most popular methods of unclogging a slow draining toilet is using hot water and liquid soap. Pour the boiling water into the bowl and then add the liquid soap. Let it sit for about 15 minutes before flushing.
You might want to see if the clog works itself out in time. If you have another toilet you can use, let the clogged one set overnight. The water pressure that builds up in the bowl might actually cause the toilet to unclog itself. After a day's wait, flush the toilet again.
Using a plunger is one of the most effective methods used for unblocking a toilet as it can unclog a wide variety of waste pipes.
Slow drainage
Water should go down quickly when you flush the toilet. If it takes a while for your toilet bowl to drain, there might be something stuck in the pipes preventing normal flow. Clogs can cause a complete blockage as well as slow drainage. Either way, you need plumber assistance if this is the issue.
So, let's recap the common reasons why a toilet won't unclog — excessive toilet paper use, non-flushable solids, hard water, and clogs in the main sewer line. Thankfully, they can be prevented via methods like double-flushing, covering the toilet bowl, routine inspections and dealing with tree roots.
The most common causes for a slow-draining toilet are: A clog in the drain line. A blockage between the tank and bowl. Poor or Clogged Venting.
A manual drain snake, also known as a plumber's snake or a drain auger, is a small boring tool that rotates slowly as it's physically pushed through a stubborn clog. The terminal end of the device is a corkscrew-shaped hook that is fed into a clogged drain or toilet.
It can hurt the toilet and soften/dissolve pipes— Drano uses caustic or oxidizing chemicals to create heat to unclog a drain. If Drano does not clear the toilet, this heat can crack the porcelain, soften PVC pipes and dissolve old, corroded pipes.
You may have a first-generation, low flow design. The low flow design was created to help homeowners save on water, but the earliest models ended up lacking the necessary pressure to properly clear the internal trap and drain. In other words, this means that it can continuously become clogged if you aren't careful.
How to Unclog a Toilet With a Plunger. After the water is turned off, try using a conventional plunger to unclog the toilet. Be sure the water covers the cup of the plunger; if it doesn't, you may need to manually control the flapper until enough water enters the bowl.
Sometimes clogs cause a toilet to slowly drain its bowl. You cannot plunge a toilet that is empty, so if there is no standing water, use a cup to fill the toilet with water from your sink. If the toilet is empty, take the opportunity to use hot (but not boiling) water, as high temperatures can help clear clogs.
Many people think that a forceful push into the plunger is what frees up the clog, but this can often worsen the problem. In fact, pushing the plunger in with enough force can even break the seal of the toilet gasket (the seal between the toilet and the floor where the plumbing exits).
Using too much toilet paper
This is probably the most common reason toilets get clogged — and often the easiest to deal with. If we're honest, most of us are probably guilty of this one. If you're one of the many people who use a lot of toilet paper when you use the bathroom, here are a few tips!
Toilets can develop drain clogs for any one of several basic reasons, usually involving partial or complete obstruction in one of the various parts of the drain system: the toilet trap, the branch drain line, the vent pipe, or the main sewer line.
Using a snake is also more invasive and time-consuming than using a chemical cleaner is, and can often become a dirty job. When it comes to getting at and removing major clogs or clogs that are deep down in your pipes, however, a plumber's snake is your best bet.