Most homes have a safety factor of 40 PSF (pounds per square foot). The important thing to remember about the safety factor is that it is spread over the entire floor from wall to wall - not just on any given area of the floor.
Normal floor allowable live load is 40 pounds per square foot (psf).
Take the total load, and divide by the overall recommended load to get the percentage. For example, if the total load is up to 800 watts and this is a 20 amp circuit, then the load usage is 800 watts divided by 1920 watts equal to 0.416 or 42%.
Most modern floors are designed to support 40 lbs./per sq. ft. so you may be okay but there are a lot of variables. Some of it would depend on the footprint of the equipment.
One of the best flooring types to anchor your gun safe to is cement. Cement is very strong and can hold a safe weighing 1,000 pounds or more without a problem. Depending on how your home is built, you'll most likely have concrete floors in your basement or in your garage.
Then I find the maximum load from the equation P = F/A where P is the stress, F is the load and A is the cross-sectional area of the pillar. Other cases, such as the bending of a beam, are much more complicated.
When calculating your maximum capacity, you must first determine your cycle time, or how long it takes to complete one unit of your product or service. Then, take the total number of available work hours multiplied by the number of employees that can complete the work, and divide the product by your cycle time.
Finally, with obtained allowable bearing capacity, calculate the allowable load (P) by using q a = P / A where A is the area of the footing and is given by A = 4.5 m × 2.25 m . Rearrange the formula and solve for P: P = q a × A . Substitute the known values into the equation to get the allowable load.
A floor limit—also known as a credit floor—is the maximum charge that a merchant will accept on a credit card without obtaining authorization from the card issuer. Floor limits are designed to limit merchants' and card issuers' potential losses from fraudulent credit card transactions.
Wooden joists can support 50 to 100 pounds per square foot.
RAISED FLOOR LOADING CAPACITY
How Much Weight Can a Raised Access Floor Hold? The weight load capacity range for standard raised access flooring ranges from 950 pounds - 1250 pounds.
Floor load capacity is the total maximum weight a floor is engineered to support over a given area. In the U.S. it is expressed as pounds per square foot. Floors are engineered to carry a maximum static load and a maximum dynamic load that can't be exceeded without the risk of compromise to the structure.
Dragging heavy furniture can cause significant scratches and gouges that are difficult and sometimes impossible to repair. If furniture is too heavy to lift, consider using furniture sliders that are specifically designed for hardwood floors.
How much depends on the thickness and quality of the tile as well as the supporting surface underneath. Typically, a porcelain tile of 3/8 to 1/2 inch thickness can withstand loads of 200 to 300 pounds per square inch.
According to the formula of loading capacity, loading capacity= [(Total amount of drug-Free amount of drug)/nanoparticles weight] x 100.
Carrying Capacity Formula
To calculate a carrying capacity, multiply the rate of population increase, by the size, then again by 1 minus the size, then finally divide by the change in size.
The overloads are determined using 125% of the FLA, 7A x 1.25 = 8.75A. The maximum allowable size for the overloads is 9.8A. The overloads can be sized at 140% of the FLA if the overloads trip at rated load or will not allow the motor to start, 7A x 1.4 = 9.8A.
Carrying Capacity can be simply calculated by subtracting the TARE Weight from the GVM.
The short answer is yes. It's your choice where your safe is installed. Our delivery team can and has installed safes on the second story of homes and office buildings.
It should be fine, put it near a wall that has main support underneath if you are worried.
The most secure place to install a safe would be at the corner where two outside walls meet. This provides the most protection and support for a heavy safe. In a house that has multiple levels, it's best to keep the safe on the ground floor.