To run diagnostics on a Whirlpool appliance, the process depends on the specific product type. However, for most Whirlpool machines, you can enter the hidden diagnostic or service mode by using a specific sequence of button presses.
To enter diagnostic mode on a Whirlpool washer, ensure the machine is in standby (plugged in with no cycle running). Use one of the two most common knob sequences below, depending on your model. You must complete the sequence within 6 to 8 seconds.
To enter diagnostic mode, ensure the washer is empty, powered off, and the dial is at the 12 o'clock position. Turn the dial three clicks right, one click left, and one click right within 6 seconds. Blinking lights or a code on the display confirms you have successfully entered diagnostic mode.
Diagnostic mode steps vary entirely depending on your device. Find your device in the list below for the specific button sequence or menu code needed to access hardware and software tests.
Turn usage & diagnostics on or off
Traditional Chinese Medicine Practitioners perform their clinical assessment through four diagnostic methods: Inspection, Listening & Smelling, Inquiring and Palpation.
Running a calibration cycle on a Whirlpool washer resets the drum sensors and re-calibrates motor speeds. It is required anytime you replace a part, fix an unbalanced tub, or move the machine.
On a Whirlpool washer, the sensing phase typically takes 2 to 3 minutes. The machine pulses the empty or lightly-loaded tub in short, slow spins to "weigh" the clothes and check for balance before adding water.
The most common problem with Whirlpool washers is a failure to spin, agitate, or drain, primarily caused by unbalanced loads or a malfunctioning lid latch/door lock. Because safety mechanisms prevent the machine from running if the door isn't properly locked, or if the load shifts unevenly, the cycle frequently stalls.
To fix an error on your Whirlpool washer, first perform a power reset to clear temporary glitches. If the error persists, use the machine's diagnostic mode to identify the specific code and inspect common mechanical issues like clogs or an unbalanced load.
The F5 E3 error code on a Whirlpool washer indicates a door or lid lock malfunction. This means the machine cannot detect if the door is fully closed, locked, or unlocked correctly. The washer will usually pause, refuse to start, or beep continuously.
Most Common Whirlpool Washer Error Codes
To put most modern Whirlpool dishwashers into diagnostic mode, press any three buttons in a rapid 1-2-3, 1-2-3, 1-2-3 sequence (allowing no more than one second between presses).
To put a Whirlpool Cabrio washer into diagnostic mode, ensure the washer is in standby mode (plugged in, screen blank). Within 8 seconds, perform the following sequence using any button except Power, Start, or Stop: Press/Hold 3 seconds, Release 3 seconds, Press/Hold 3 seconds, Release 3 seconds, Press/Hold 3 seconds.
Unplug the washer and let it sit for about one minute to drain stored power and memory. Plug the washer back in, and let it sit for a few moments. Open and close the lid six times in under 12 seconds.
To put your Whirlpool washer into diagnostic mode, clear all clothes, close the lid, and make sure the machine is in standby (no cycle running). For most dial-controlled models, turn the knob 360 degrees counterclockwise to reset. Then, quickly turn the dial in this precise sequence: Left, Right, Right, Right, Left, Right.
After scientists discover the causative agent of an emerging infectious disease, such as Borrelia burgdorferi or Ehrlichia chaffeensis, they develop, evaluate, and refine diagnostic tests over time. Diagnosis, by contrast, rests on a patient's history and symptoms and observed physical and laboratory findings.
A diagnostic test is a systematic process used to identify underlying conditions, causes of errors, or areas of strength and weakness. Whether in healthcare or education, diagnosis relies on a structured, multi-step sequence to ensure accurate results and targeted follow-up actions.
According to Traditional Chinese Medicine (TCM) and their 24-hour organ clock, the liver is the organ cleansing between 1 a.m. and 3 a.m. The lungs undergo a similar replenishing process from 3 a.m. to 5 a.m.
Do one of the following: