In AC systems, the air conditioner reset button is on the outside unit's lower edge, typically close to the ground. Some models have the reset button located behind the service panel, which may require tools to remove. Reset buttons are usually red or yellow with a clear “reset” label.
You can find it on the wall beside the unit or at the condenser. The isolation switch looks like an ordinary light switch with a knob. Once you locate it, turn the knob to the off position and leave it for at least 30 minutes up to an hour. This will allow the electrically operated components in the AC to reset.
Make sure the outside unit is turned on (there's probably a switch near the unit). If the outside unit has a separate circuit breaker, check your circuit box and make sure it hasn't been tripped. A more serious issue if the outside air conditioning unit's not working is a broken compressor, capacitor or fan.
As mentioned, one of the more common reasons for an AC unit needing a reset is due to the protection circuit breaker inside the unit kicking in. This usually happens after a power outage occurs, and this failsafe is in place to prevent fires and explosions from occurring from a power surge.
In some cases, clogged air filters or dirty evaporator coils can also restrict airflow, forcing the AC to compensate by running at high power. To resolve this issue, it's recommended to check for clogged filters, clean coils, and consider having a professional inspect and repair the motor or fan control components.
First, check your filters and coils for dirt and debris that may be impeding airflow. Once you've cleaned the filters and coils, run the air conditioner with just the fan so that the ice accumulation can melt off. If the AC still doesn't blow cold air, it could be that refrigerant levels are too low.
Resetting your thermostat is an easy first step in troubleshooting temperature control issues. If problems persist after a reset, you should contact an HVAC technician for additional diagnostics and repairs.
For AC capacitor replacement, anticipate spending between $150 and $400, depending on the capacitor's type and accessibility. A bad AC capacitor is a fairly minor repair, and most HVAC technicians will recommend a repair rather than replacing the unit when the capacitor is the problem.
When the outside unit breaks down but the inside unit is running, the culprit may well be a broken compressor in the outside unit. That's typically a major repair, something that might even warrant a system replacement.
If you think your air conditioner has blown a fuse, the first sign you'll notice is that the outside AC unit is inoperable. The best way to check for a blown fuse is by using a voltmeter. Be warned — you are working with live electricity and should use extreme caution when troubleshooting your system.
The main reasons your AC unit outside is not turning on could be something that has tripped the circuit breaker, something is blocking the fan's airflow, or the condensing unit is damaged. Other potential issues could be the thermostat isn't set correctly or the compressor could be malfunctioning.
FIND THE RESET BUTTON
In most cases, the small red reset button is inside the AC's compressor. If unsure, you can always refer to the user's manual to find the exact location.
Shut off your system by hitting the isolation switch, wait 30 to 60 minutes and then turn it back on. This manual reboot fully disconnects your AC unit from power, allowing all electrical components to reset.
Some air conditioning systems have a reset switch, which is a small, red button. Typically, the button will be on the outdoor unit. If you have a problem locating it on the outdoor unit, you may find relevant details on the equipment's manufacturer's manual. Press the red button for three seconds and release.
Common Reasons Why Your Air Conditioner is Not Turning On
Resetting your thermostat is often all that's necessary to get it working again. A tripped circuit breaker is another common reason why your AC won't turn on. Using too many appliances at once can trip the circuit breaker.
Locating the Reset Button
Remove the thermostat cover by either snapping it off or unscrewing it, depending on the model. Most modern thermostats will have a clearly marked reset button inside the panel. It's usually small and recessed, so you might need a pointed object like a paperclip to press it.
There are a number of reasons why your air conditioner might be running but not cooling. It could be an issue with the thermostat, the compressor, or the evaporator coils. Or, it could simply be clogged with dust and debris, which is preventing it from working properly.
If your air conditioning unit is ac blowing cold air outside, it might mean there's a problem with cooling the air inside. This could be due to refrigerant leaks, frozen coils, electrical issues, or airflow problems. It's important to find out why to fix it and keep the cold air inside.
Signs Of Clogged Coils
This could manifest itself through reduced cooling power, increased energy bills, musty odors, or excessive condensation on windows and walls. Additionally, the AC unit may make louder noises than usual or be struggling to keep up with demand.