First, you want to mix a quarter cup of white vinegar with a litre of hot water and douse the surface of the tub. Grab a handful of baking soda and toss it over the surface of the bathtub. Let it sit for about 30 minutes before scrubbing and rinse your tub clean. Baking soda should help to whiten your tub.
We would recommend using a solution of white vinegar and water to initially soak your bath. The natural acidity in the vinegar helps to dissolve soap scum and limescale, the normal residues you'll find in a bath. Follow this up by sprinkling baking soda and then spraying your white vinegar/water solution.
Equally combine warm water, ammonia and baking soda into a bucket. For tough stains, first cover them throughout the tub with salt and lemon juice, then allow it to sit for up to 1 hour. Scrub the salt and lemon juice into the stain. Dip a cloth or soft sponge into the bucket and scrub the tub thoroughly.
Use Distilled White Vinegar
For weekly cleaning of sinks, tubs, and shower walls, spray the vinegar on the rust stains. Use a scrub brush to clean the area and then rinse well. For weekly cleaning of rusty toilet bowls, add one to two cups of vinegar to the bowl and scrub with a toilet brush.
Painting a bathtub with a refinishing kit
As stated above, changing the color of your bathtub will usually involve a prepackaged kit. These kits can be found at any online retailer or your local home improvement store and contain a chemical compound that will replace the finish on your bathtub.
Baking Soda and Vinegar
Add vinegar to the mix and you can say goodbye to the dust, soap residue, and mineral stains that are making your bathtub look dull. Good for both porcelain and acrylic bathtubs, a baking soda and vinegar solution safely polishes the surface without scratching.
Like magic, the Magic Eraser will start powering through tough grime in just a few swipes. Before you know it, your clean bathtub with shine like the top of Mr. Clean's head! And remember, you can also use Magic Eraser to clean other surfaces too.
Whether or not bleach can damage a bathtub will depend on its material. Fiberglass, white porcelain, ceramic, stone, and cultured marble are bleach friendly and will not become damaged. Wooden, acrylic, cast iron, and copper bathtubs can not be cleaned with bleach, as they will become damaged.
Make a paste of one part hydrogen peroxide and two parts baking soda. Use a sponge to scrub the stubborn spots with baking soda and peroxide. Let the paste work on the bathtub stains for an hour. Rinse the bathtub with hot water.
Plastic bathtub refinishing is similar to the process of refinishing and repairing porcelain and fiberglass bathtubs. First, the surface must be chemically cleaned to remove any soap scum, mineral deposits, or body oils. Next, all cracks and chips are filled and sanded smooth.
Soak a non-abrasive sponge in the baking soda/ammonia solution and scrub the surface of your porcelain bathtub or sink, paying particular attention to stained areas. Dip the sponge in the solution, scrub and repeat until you're satisfied. Rinse well.
Your tub's structure needs to be in good condition, but refinishing can extend its life span. Bathtub refinishing typically costs $335 to $628 with a national average of $481. * Compare that to full bathtub replacement, which costs into the thousands. We'll go over various factors that affect refinishing prices below.
Spray Painting a Bathtub Isn't a Great Idea
For starters, most spray paints are not made to adhere to slick tub surfaces. You could lightly sand your tub before painting, but you're still not going to get great adhesion. Spray paint is much thinner than traditional paint, and it cannot withstand a ton of wear.
If cost is the most important factor in your decision, you should opt to reglaze your bathtub. You will spend the least money and, if you care for it properly, it will last for decades. If cost is not as much of a concern, PureCoat will undoubtedly be your best option for refinishing your tub. Time.
Unlike your standard interior paint options, which will crack and peel at the amount of heat and moisture tubs are exposed to daily, epoxy boasts great adhesion and long-lasting durability once cured. A one-quart kit should be enough to cover the bathtub, but pick up two if you also plan to paint the surrounding tile.
Regular paint will not be able to withstand water. Acrylic polymer paints are one of your best options for an acrylic bath. Whereas for a cast iron tub, the bath paint must be suitable for metal. An oil-based primer and paint is best for this type of bath.
In most cases, refinishing a bathtub is the best option. Almost all tub styles can be refinished, including cast iron, steel, acrylic, fiberglass, and porcelain tubs. Refinishing a bathtub is worth it if: You like the style of your bathtub, but it needs a fresh look.
Hydrogen peroxide does a great job of removing hard water stains and is a less harsh alternative to bleach. Spray a solution made from equal parts hydrogen peroxide and water over your tub and leave it for 20 minutes. Then, scrub any remaining stains with a household sponge.
Hard Water
These limescale deposits can build up over time until they have a raised texture as well as an odd color. While limescale in the bathtub may not look attractive, you can usually remove it with special cleaners and elbow grease. Hard water may also cause orange or brown stains in fixtures that look like rust.