Turn off the hot and cold water on the wall. Get a small bucket to catch any dripping water. Unscrew the hoses from the back of the washer. You will find a small water filter screen on each end of the hose. Clean these filters and the surrounding area. If the filters are damaged or caked with hard water, replace them.
The most common reason is a problem with the water supply, or a blocked or kinked water supply hose. In this situation, the washing machine will drain for 3 minutes and the power button will be inoperative. In this case, please clean the debris filter and mesh filter.
Check Water Flow
Check for water flow through the fill hoses by unplugging the washer, turning off the faucets and disconnecting the hoses from the back of the washer. Hold each hose end over a bucket and briefly turn on the faucet. If you don't have any water coming out, check for a clog in the hoses.
Washer Control Reset
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Why is my washing machine humming and not filling with water? If your washing machine isn't filling with water and is making a humming sound, it could be related to water flow problems, such as closed or blocked supply taps. Check the water supply and connections to address this issue.
Is it filling up when not in use? If you find clean water filling up the drum when the washer is not being used this could be due to contamination from your cold water supply clogging in the water valve of your washing machine. There is a filter fitted in the valve to catch this debris and can be easily cleaned.
If the water pump is running but no fluid is being pumped this could be blocked inlet suction filter, check valves failed with pumps bypassing, blocked discharge lines, electric motor polarity is incorrect or incorrect pressure settings parameters amongst other issues.
A pump can fail in two ways: mechanically and electrically. A mechanical failure can be caused by a foreign object caught in the pump, or direct damage to a pump component, such as the impeller, which can cause the washer to not drain. Inspecting the pump can often reveal a mechanical failure.
Clothing That Feels Heavy After a Cycle: When your clothes are unusually damp even after a spin cycle, it's a sign that the machine isn't draining effectively, which usually points to the filter! Water Leakage: Unexpected puddles around your washing machine might indicate pressure buildup caused by a clogged filter.
Use a funnel to pour about a quarter of a cup of baking soda into the pipe. Next, empty a baster full of vinegar into the drain hose. Top tip: If the blockage is not completely gone, you can repeat the above process. Once you have cleared any debris from the hose, pour hot water in to flush everything out.
Typically a washing machine lasts 10-13 years. Top-loading washers typically last a few years longer than their front-loading brethren. If you use a stacked washer/dryer combo, you may have to replace both if one starts acting up. Proper maintenance will likely help your washer last for over 15 years.
Some reasons for a washer not filling with water include issues with the lid switch, a kinked hose, clogs, damaged switches, and malfunctioning electronic controls or timers. It's wise to let an appliance repair professional handle washer issues to avoid damaging the machine further.
Check the inlet valve and filter
There's a small filter on the inlet valve where the hose connects to the machine. This filter stops any debris in the water getting into your washing machine. Over time, it can become clogged with things like sand and sediment.
If your appliance won't take water in and you hear this humming then it usually means there is a problem with the taps at the back of your machine. The gentle humming means that your washing machine's taps are trying to take water in but can't, so first things first you should check the taps.
If you want to try resolving issues with your washing machine, such as power surges or error codes, it's possible you might need to perform a quick reset. One way you can reset a washer is by unplugging the unit for at least one minute, then plugging it back in and restarting the appliance.
A blocked detergent line or tray is the most likely reason for your washing machine not cleaning your clothes properly. Alternatively, there could be a blockage elsewhere, meaning that detergent, germs, dirt and grime will eventually build up and transfer onto your clothes.
Check for any kinks in inlet hoses, which can restrict water flow. If possible, remove the inlet hoses from the back of the washer. To do this, turn the water supply off, then use pliers to remove the hoses. Place hose ends in a bucket to catch water remaining in the hoses.