Double models: Press and hold to cancel a wash that has already started or to cancel the delay start setting. Opening the drawer will automatically turn the dishwasher on. Single models: Press to turn the dishdrawer on or off.
1 Open the door carefully to pause the programme. 2 Touch and hold to cancel the programme. 3 Touch any button to turn the dishwasher back on, and follow the steps above “To start a wash programme”.
On most models, pressing and holding the Start or Start/Reset pad for 3 seconds will cancel any set cycle, including the Delay Start cycle.
Switch the power off at the socket, wait 60 seconds and switch on again (this may reset your DishDrawer™). Either test the socket by plugging in a different appliance, or by plugging your dishwasher into a different power socket. DishDrawer® to turn on automatically, this feature can be turned off.
To cancel keylock/childlock: If the drawer is open Press and hold until you hear a tone. The lock indicator will go out. If the drawer is closed Knock three times on the door. START SELECTOR (either on door or inner control panel) To start wash: Press to start the wash.
Turn the Keylock or Child lock off. Hold down the button until the symbol disappears from the display or the light above the button goes out and/or press the button to open the drawer. Turn off Keylock as per your Quickstart Guide as this function locks the controls.
To LOCK/UNLOCK the dishwasher control, depending on the model, press and hold the Cycle pad, or the Dry/Dry Boost and Steam pads simultaneously for 3 seconds. The Lock Controls light will turn on to indicate the control is locked and will turn off to indicate the control is unlocked.
Double models: Press and hold to cancel a wash that has already started or to cancel the delay start setting. Opening the drawer will automatically turn the dishwasher on. Single models: Press to turn the dishdrawer on or off. Press to turn the dishdrawer on.
While you can stop a dishwasher mid-cycle, you should avoid doing so if you can. It takes more energy to restart and bring the heat back up. If you stop the cycle and add items after the detergent has been released, they may not get as clean.
Some models require you to shut off the power to the dishwasher either by unplugging it or shutting off the circuit breaker. Others are reset by pressing and holding the Start/Reset button on the control panel, then waiting a few moments before attempting to start a wash cycle.
1 Check if the water supply has been turned off or the wash program interrupted. 2 Press and hold once to stop the beeping and then again to clear the alert code.
1 POWER Press to turn the washer ON/OFF. 2 Wash Cycles Turn the dial to select the desired cycle for your load. 3 Remote Press and hold to control washer from the Fisher & Paykel app when Wi-Fi is enabled.
Press to start the wash and close the drawer within 7 seconds. Press and hold . If there is any water in the drawer, it will automatically drain before the DishDrawer™ Dishwasher turns off.
If your dishwasher keeps running non-stop and won't shut off, it's possible that a malfunctioning drain pump is to blame. After the wash cycle, if the control senses water remaining in the sump, it might activate the drain pump to eliminate the water.
To cancel: press and hold until the indicator stops flashing and goes out. Start Press to start the wash. To pause: Press again. The drawer indicator light will flash.
Cancel a Wash Cycle
If you need to interrupt a cycle that has already started, follow these steps: Hold the "Start/Pause" or "Power/Cancel" (depending on the model) button for 3 - 5 seconds. This will cancel the cycle and drain the water from the washer.
Canceling DISH service
To cancel DISH, call 1-866-218-2297.
Hold the start/reset button – If unplugging the dishwasher didn't work, the next thing you can try is pressing and holding the start or reset button for at least one full minute. All you have to do now is cross your fingers and hope it works.
Press and hold the LOCK button for 3 seconds to lock or unlock the control panel.