A minimum of 12”inches deep for all footings and the width will be determined by the amount of stories, 12” inches for a single story, 15” inches for a two story and 23” inches for a three story. This is based on a soil bearing capacity of 1500(psf).
As specified by ACI-318, a minimum of 3 inches of concrete cover over steel reinforcement is required when concrete is in contact with soil. In addition, ACI-318 does not permit a depth less than 6 inches for reinforced footings supported by soil.
The minimum depth of footings below the surface of undisturbed soil, compacted fill material or controlled low strength material (CLSM) shall be 12 inches (305 mm). Where applicable, the requirements of CBC Section 1809.5 shall also be satisfied. The minimum width of footings shall be 12 inches (305 mm).
Required Footing Sizes
In most cases, a house should have a minimum footing of 12 inches wide by 12 inches deep, with foundations that are 8 to 10 inches thick. This should be enough to support house weight and resist lateral soil and water pressure.
While there are many factors at play, a common rule of thumb for foundation depth is to go as deep as the width of the foundation wall. For instance, if your foundation wall is 8 inches wide, a depth of 8 inches is a starting point.
The thickness of the footings should be not less than 200mm and is usually mass concrete only, ie. no reinforcement. The depth below ground level to the base of the footing should be not less than 300mm or to rock, whichever occurs first, which allows for a minimum of 100mm of ground cover to the pad.
Gravel provides drainage, stabilizes the soil, prevents erosion, and helps distribute weight more evenly. Without it, you risk the potential damages listed above. If you're planning a concrete project, don't skip the gravel layer—it's a foundation that ensures your concrete work stands the test of time.
All foundations shall extend to a depth of at least 50 cm below the natural ground level. The minimum depth of footing on sandy soil is 0.8 - 1 m, for rocky soil, it is 0.05 - 0.5 m and for clayey soil, it is 0.9 - 1.6 m. The minimum depth of foundation for the load-bearing wall is 900 mm.
Footings shall be a minimum of 8 inches by 24 inches (203 mm by 610 mm) for houses two and one-half stories and less. The footings for a three-story building shall be 10 inches by 24 inches (254 mm by 610 mm).
Additionally, it's important to consider local building codes, soil conditions, and whether you need to account for frost lines, which can require deeper footings in colder climates. Generally, footings should extend at least 12 inches below undisturbed soil or below the frost line, whichever is deeper.
The footing is what's actually in contact with the ground, while the foundation is the structure that transfers the load to the earth. A simple way to visualize the difference when comparing it to the human body would be to view the footing as the actual feet of the legs and the foundation being the legs themselves.
Depth of footing above bottom reinforcement shall not be less than 150 mm for footings on soil, nor less than 300 mm for footings on piles.
Generally, a minimum of two #4 bars are required for residential footing. The rebar should be placed in a grid pattern with a spacing of no more than 18 inches apart. It is important to follow these minimum requirements to ensure that the footing can withstand the weight and pressure of the structure above.
First off: Why you need accurate footings calculations
If you make your foundations too shallow or too deep, there is a risk to the integrity of the build, and a danger that any reinforcement, be it mesh panels or rebar rods, is positioned incorrectly, leading to reduced tensile strength and load-bearing capacity.
A minimum of 12”inches deep for all footings and the width will be determined by the amount of stories, 12” inches for a single story, 15” inches for a two story and 23” inches for a three story. This is based on a soil bearing capacity of 1500(psf).
The footing depth, on the other hand, is typically determined by the soil type and the extent to which you must dig before striking undisturbed soil. Still, we recommend that the depth of the footing extends to a minimum of 12 inches after you've hit undisturbed soil.
In reinforced and plain concrete footings, the thickness at the edge shall be not less than 150 mm for footings on soils.
It is not advisable to pour concrete directly on dirt. Even compacted soil—known as a subgrade—is not strong enough to maintain the form of concrete. You can, however, pour concrete over concrete as long as the overlay has proper bonding agents and the slab below is clear of damage.
Choosing the right material for your sub-base is crucial in the overall performance of your concrete base. The most commonly used materials for a sub-base include gravel, crushed stone, and sand. Gravel: It's a popular choice due to its excellent drainage properties and ability to distribute the load evenly.
The Gravel Provides a Level Surface and Helps Drainage.
Gravel is used to level the slab and help with drainage. The water that runs off the surface of a concrete slab will cause erosion, which can damage your home's foundation over time.
Even the best contractors occasionally have to build on a sloppy footing. Ian Geisler, a noted ICF expert who has worked on hundreds of projects across the continent, says that realistically a perfect footing is anything within ¼” of level. “If it's within ½”, then it's workable,” he writes.
A concrete mix of 1 part cement : 2 parts sand : 4 parts coarse aggregate (by volume) should be used for footings. Concrete must be placed within half an hour of mixing. Brickwork – Place your concrete into your trench. Work the concrete into awkward places and corners using a shovel.
Spread Column Footings are constructed with typical footing heights between 8”-24” (20-61 cm) and footing widths of 24”-96” (61-244 cm). Spread Column Footings are commonly paired with column widths of 8”-24” (20-61 cm).