Electrical wires generally sit at a depth of about 1 to 2.5 inches (25 mm to 64 mm) beneath the surface of a wall, depending on the wall type and local building practices. Because building codes prioritize safety and protection, hidden wires typically adhere to these depth standards and routing conventions:
As with installing indoor wiring, there are some rules to follow. Most of the rules involve protection of the wiring from damage. The NEC (National Electrical Code) requires that UF cable be placed in a trench at least 24 inches deep.
Anonymous user. All electrical cables should be set into the walls at a minimum depth of 50mm if they are not mechanically protected. If it isn't possible to chase the walls to that depth then the cables should be set deep enough so that metal capping can cover them and allow for plaster to cover that.
Don't drill directly above or below an outlet or switch because the wires are generally run vertically in the US & Canada but in some other places I've seen the run diagonally. Generally stay 6" away from that vertical line of the plug. Some wires run horizontal, like from one plug to the next.
A cable detector—also known as a stud finder, wire detector, or multifunction detector—helps identify hidden objects and reduces the risk of accidents. There are several types of cable detectors: Magnetic Detectors: Identify metal objects like screws or nails.
"Use a decent digital detector (like this Bosch Truvo detector from Amazon) to check for pipes, cables, and studs, especially near sockets or light switches. It's never worth the risk of drilling into walls without checking first.”
MultiScanner™ 440 quickly and easily locates studs, metal, and live electrical wiring behind walls, floors, and ceilings. A 4-mode switch makes it easy to change functions, while the easy-to-read display screen, SpotLite® Pointing System, and audio tone all indicate the location of the target.
Investing in professional equipment, such as a cable avoidance tool, is the safest option to avoid wires. However, if you don't have access to this, most wiring runs horizontally 6 inches or 12 inches above the receptacle, so avoid these areas. If it is possible, only drill shallow holes.
In single brick walls, electricians cut (chase) into the bricks to run your wiring. But with double brick, it's much easier, the wiring just feeds straight down through the cavity. It's the kind of detail you never see… but it's what makes the whole thing work.
Yes, asbestos was used in electrical wiring and other components between the 1930s and early 1980s. Asbestos was believed to be a safe way to keep electric wires well-insulated and protect them from corrosion.
Modern cables can be buried directly in plaster, or protected with capping before plastering. Before a cable can be buried however, a chase needs to be cut! See the wall chaser article for more detail on the options for cutting cable chases in plaster and masonry.
So where should you expect to find the wires running? Top of the wall - where the wall meets the ceiling there is a 150mm zone where wires should be run. This runs horizontally around the whole room. Join between two walls - there is a safety zone of 150mm on each wall from the join where the two walls meet.
Vertical chases should not be deeper than 1⁄3 of the wall thickness or, in cavity walls, 1⁄3 of the thickness of the leaf. Horizontal chases should not be deeper than 1⁄6 of the thickness of the wall or leaf.
By working with one hand (keeping the other hand in your pocket or behind your back), you minimize the chance of creating a closed circuit and current passing through vital organs.
The three basic rules of wiring are as follows:
Drilling into a concealed cable is always a nasty shock – and it's seriously dangerous if the wire is live. Electrocution can result when a live cable is damaged and makes contact with the drill, forming a circuit through the user's body. Another danger is fire risk resulting from damage to wiring.
Rewiring a house is a significant project, but it doesn't have to involve tearing down walls and creating a mess. With modern techniques like fishing wires and using flexible conduit, skilled electricians can upgrade your home's electrical system with minimal disruption to your drywall.
The total degree of bends in any combination of conduit or tubing wiring methods used for a single run shall not exceed 360 degrees between pull points. B: The total degree of bends in any conduit in multiple runs shall not exceed 360 degrees between transition fittings.
You're using the wrong equipment. If you're not using a powerful enough drill (you probably need one with a hammer action) then you might find that your drill is unable to drill into the brick. Using the wrong drill bit will also mean you're unable to drill a hole.
A nicked wire can indeed cause a circuit breaker to trip. When the exposed part of the wire touches another wire or a conductive surface, it creates a short circuit, leading to a sudden surge of electrical current.
So safe bet is don't drill on walls on top electrical socket. In theory, wires are run straight up & down, and horizontally left & right. Sounds good, but even if you avoid drilling directly above and directly beside a switch or socket point, you might still drill into wires.
Damage to electrical wiring from drilling into walls is a surprisingly frequent phenomenon – especially when buildings are being renovated. Not only do the lights go out, but you usually blow a fuse as well. With a bit of luck, you might only have to repair the cable sheath.
Another practice of finding electrical wires behind walls is to use a metal detector. This can be an efficient method if you know there are very few wires and if there aren't many other metal objects, like nails, in the walls.