Simply go to one bathroom, and turn on all faucets/showers. Once all the fixtures are on, flush the toilet to see if the water drops pressure from the sinks or shower heads. If water pressure drops while the toilet is filling up, there might be an issue. You should complete this process for all rooms that have water.
A fast drop in only one faucet means there's a problem with the faucet. Rapid low pressure affecting one area of the house may mean a corroded pipe issue. An abrupt water pressure drop affecting the whole house may mean a water main break (municipal water) or a well pump problem (well water).
It may be caused by debris such as dirt, sand, solidified oil and grease, food particles, or foreign objects. Pollutants can block pipes if they back up due to fractures in the water main. Mineral buildup clogs pipes over time and causes the water pressure to go down, as there's less space for water to travel through.
Open your main water valve.
Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure. Sometimes the main valve is turned off accidentally during routine repairs and maintenance without the homeowner's knowledge.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
A quick and easy way to increase water pressure (for homes supplied by a municipal water system) is to adjust the pressure-reducing valve, which can be found on the main water-supply pipe; look for a conical-shaped valve next to the water meter, close to where the main water pipe enters the house.
If there's an accumulation of sediments in your hot water tank, it can lower your water pressure. The presence of kinks in the flexible water pipes used in water heaters can result in low water pressure. If the shut-off valve isn't fully open, water pressure can drop.
In general, residential water pressure ranges between 45-80 psi (pounds per square inch). If your water pressure is under 40 psi, it's considered low. A psi between 20-30 is considered very low, and under the minimum water pressure required by most building codes.
The most common cause of low shower pressure is a blocked showerhead, as a result of limescale build-up. These blockages obstruct the water flow, leading to reduced pressure over time. Most showers are fitted with a filter, protecting the pipework from debris, but this can become partially blocked by scale.
The city could be flushing hydrants.
In any of these cases, the pressure loss will be temporary. But when the water does come back online, it will definitely kick up sediment, which can clog supply valves and faucet aerators. Be prepared to flush them if the pressure seems low when the water comes back on.
A quick and easy way to increase water pressure is to adjust the pressure-reducing valve, which can be found in your home, usually close to your water meter.
Do All Homes Have a Water Pressure Regulator? No, and in some cases, you may not need one. Certain municipal supplies regulate their water pressure safely, but if that pressure runs above 80 psi, you'll want to protect your plumbing system by installing one.
Typically, water pressure regulators cost about $50 to $100 on average1, though you could end up paying up to $2001 depending on the size of incoming water line.
How long will a Water Pressure Reducing Valve last? The life expectancy of a water pressure regulator is most commonly in the range of 10 to 15 years. However, you may see a regulator malfunction at three years and one still properly functioning at 20 years old if regularly maintained.
Homeowners should start first at one faucet in the house, like the kitchen or bathroom sink. They should turn on cold water first and then hot water, before turning on both, while noting when water pressure is low and when it is not. Next, they should try the water pressure in another faucet by repeating this process.
One of the most common causes of low pressure to a kitchen or bathroom sink faucet is debris or mineral buildup in the aerator. The aerator is the tiny screen that you see at the end of your faucet.
The good news is that you can easily replace faucet aerators, clean showerheads to remove limescale, or simply buy new fixtures to replace the defective ones, which can improve your water pressure. However, it is important to know that repairing or replacing faucets and fixtures is only a temporary solution.
Clogged aerators and clogged cartridges are two of the most common causes of low water pressure in a sink. The aerator is the tip of the faucet that the water comes out of, while the cartridge is found underneath the sink handle and enables you to stop and start the flow of water.
Check Your Aerator
If you have especially hard water, aerators become clogged with hard water buildup, a common cause of low water pressure in kitchen fixtures. Clean your aerator for a quick and easy DIY fix. Remove the aerator from the faucet using pliers and a towel (to prevent scratching).
Most low-flow showerheads have a rubber pressure-reducing valve (called a regulator) to maintain a lower pressure. You can increase the flow by simply taking it out. You could also consider enlarging the hole that allows water into your showerhead with a drill to increase the amount of water coming through.