Good Growing Tip of the Week: For both aluminum and brass fittings you can also lubricate the threads with silicone grease to prevent corrosion and fusing of the fittings.
A good garden hose should last five to 10 years with proper care, but you'll need to replace that hose a whole lot sooner if you don't maintain it the right way.
Simply push your push-fit hose connectors onto the extension joint. The quick release connectors mean adjusting your hoses length takes a matter of seconds. If you want a connection which doesn't release all the water when you release the connector then use a water stop.
Spray Protectant. Using an engine protectant every few months will keep your hoses looking clean, your rubber moist and flexible (drying out causes cracking), and extend the amount of time between repairs.
The Hozelock Double Male Connector is a practical and durable solution for joining two hoses together using standard hose connectors. Whether you're extending the length of your garden hose or making a quick repair, this connector is a must-have accessory for any garden.
Heating in hot water will soften many hoses without overheating or burning.
What is the best lubricant to use on rubber parts? One lubricant that works well on rubber parts is silicone lubricant. This lubricant's versatility makes it compatible not only with rubber but with many other materials, including plastic, metal,wood and painted surfaces.
Compare this to hose threads, which utilize a washer or rubber gasket to create the seal. In basic terms, plumbing tape should never be used on garden hoses, hose bibs, and any other hose connections with a gasket as it can make the connection more prone to leaking.
Typically, a good-quality garden hose can last anywhere from 5 to 10 years. These hoses are usually exposed to the elements, dealing with heat, UV rays, and sometimes, freezing conditions, which all can impact their longevity.
The length of your hose can seriously affect the garden hose flow rate, as the longer the hose, the less water pressure there will be. This is because as water travels down the hose, it can lose pressure and offer far less flow rate, commonly referred to as friction loss.
Most manufacturers will recommend having your hoses replaced once every four years. Obviously this time period can be increase/decreased depending on different factors such as mileage, weather condition, etc.. A Car that is used and driven a lot more than a car that isn't, will need the hoses replacing much sooner.
For preventing corrosion of hose ends, WD-40 is a great solution. Every once in a while, you need to apply WD-40 to the garden hose ends. As a result, corrosion will not be an issue for you.
MOLYKOTE® G-N Metal Assembly Paste. Extreme-pressure Lubricant for assembly, press fitting, threaded connections, running-in and maintenance.
You can use bleach or white vinegar to clean your garden hose. Rubber garden hoses are pretty easy to clean.
WD-40 Specialist® Silicone Lubricant safely lubricates, resists water and protects metal and non-metal surfaces such as rubber, plastic and vinyl.
Vaseline is a petroleum product, and will rot certain types of rubber. You should never put it on brake parts and seals for instance. Other types of rubber, chlorinated polymers, have good resistance to petroleums, but it is hard to know which rubber is which unless you are an expert.
The answer is warm it up. You can soak it in hot water or take in the house or just leave it in the sun. It will never be as flexible as a good hose under the same conditions, but it will be better than a cold version of the same hose.
Q: Why do hoses get stiffer over time? A: It is true that hoses, particularly those made out of vinyl chloride, can become stiffer with continued use. Vinyl chloride resin is ordinarily a hard material often used in pipes.
If your leak is within a foot of the male or female end connectors, simply cut off the end of the hose and replace the garden hose connector with a new one. If your leak is more in the center of the hose, trim out the damaged section and splice the hose back together with a repair hose coupling or mender.
Garden hoses can be joined with hose connectors which is a union with two male ends that Connect the ends of both hoses together. Alternatively you can use a piece of half inch copper tube and stretch the hose over the ends and use hose clips to hold the hoses tight on the copper.
You can connect multiple hoses, but just make sure you consider that the pressure towards the end of the second hose will be slightly less than closer to the water source. Try to consider the water needs of your plants when connecting and laying out your hoses.
All garden hoses have the same size fittings. I pereonally have a 5/8 and it fits. It is the best nozzle I have ever had. Thank you for your feedback!