A quick and easy way to increase water pressure is to adjust the pressure-reducing valve, which can be found in your home, usually close to your water meter.
Open your main water valve.
Your house has a main water valve, usually located near the meter; the valve controls the flow of water into your home's pipes. Find the valve and check to see if it's completely open. Opening a half-shut valve is one of the quickest ways for increasing home water pressure.
A fast drop in only one faucet means there's a problem with the faucet. Rapid low pressure affecting one area of the house may mean a corroded pipe issue. An abrupt water pressure drop affecting the whole house may mean a water main break (municipal water) or a well pump problem (well water).
It may be caused by debris such as dirt, sand, solidified oil and grease, food particles, or foreign objects. Pollutants can block pipes if they back up due to fractures in the water main. Mineral buildup clogs pipes over time and causes the water pressure to go down, as there's less space for water to travel through.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
The pressure level can vary, but 60 PSI (pounds per square inch) is recommended for most residential homes. Water pressure should not be higher than 80 PSI. Anything higher can cause major appliances, including water heaters and toilets, to stop working properly because of the stress on plumbing and other parts.
Water has the unfortunate quality of being heavier than air. In fact, it weighs 62.4 pounds per cubic foot. This mass requires a pressure of 0.433 psi to lift water one foot (62.4 lbs/144 in in ft). To put it another way, one psi will lift water 2.31 feet (1/0.433).
Water is essentially incompressible, especially under normal conditions. Yet, in industrial applications water can be tremendously compressed and used to do things like cut through metal.
Sure, it's an annoying issue but it can also signal a larger plumbing problem. Low pressure in a shower can be caused by several issues such as a clogged showerhead, a worn-out mixing valve, closed valve, leaking pipe, or even a faulty water heater.
Check Your Faucet Cartridge
Your faucet cartridge sits deeper in your faucet than your aerator and has a hole through which water passes. These cartridges become clogged or blocked by hard water build up which produces low water pressure in kitchen faucets. Often, they just need to be cleaned.
If a water storage tank is elevated high enough, gravity alone can trigger water pressure identical to that of large water booster pumps.
The most accurate method is to buy a pressure gauge from your local hardware store and hook it up to a hose faucet. Check the pressure when all other faucets and water-using appliances are turned off to get a baseline reading. In general, you want the household plumbing to provide between 30 and 80 psi.
Most residential plumbing systems are designed to handle 40 to 60 PSI of pressure, with 80 PSI being the typical maximum and anything over 100 PSI being possibly detrimental to plumbing components.
If the pressure is 35-60psi, that is enough pressure and flow to allow most plumbing fixtures to work properly, unless there is a restriction within the system obstructing the flow from what it should be.
50 psi x 144 square inches/square feet / 62.4 pounds/cubic feet yields 115 feet of water height. So you'd need a barrel of water 115 feet high to create 50 psi of water pressure.
High or low water pressure can damage your pipes, fixtures, or appliances, which costs you more money in the long run.
If there's an accumulation of sediments in your hot water tank, it can lower your water pressure. The presence of kinks in the flexible water pipes used in water heaters can result in low water pressure. If the shut-off valve isn't fully open, water pressure can drop.