To get more heat from your chimney, you need to maximize combustion and stop warm air from escaping up the flue. The most effective solutions include upgrading to a Woodland Direct Fireplace Insert, burning dry, seasoned hardwood, and installing a heat exchanger or blower.
If your damper is warped, rusted or otherwise damaged, cold air in the upper flue is going to get past it. Along with the common throat damper located just above the firebox, some homeowners add a top-sealing damper at the top of the chimney to double their protection.
Up to 90% of the heat generated by an open, traditional wood-burning fireplace is lost up the chimney. Even when a fire is not burning, an unsealed chimney acts like a giant vacuum and can cause up to 20% to 30% of your home's total heated air to escape outside.
Issues may arise from a variety of factors: creosote build up or other blockages in the chimney flue, insufficient ventilation, or negative air pressure within the home. These factors impact not only the heat of your fires, but also the safe usage of your fireplace system.
5 Simple Ways to Get More Heat Out of Your Fireplace
However, if you have a smaller fire pit (less than 3 feet in diameter), you may only need 2-3 logs per hour. Conversely, for larger fire pits (over 4 feet in diameter) or if you're aiming for a roaring fire, you might need 5-6 logs per hour.
How to Increase the Efficiency of Your Fireplace
Fires in an open hearth are about 10% efficient. 90% of the heat generated goes up, literally, in smoke. Add glass doors and you've increased the efficiency to a whopping 20%. More troubling is that the chimney is doing exactly what it is designed to do, which is to take the hot air out of the fireplace.
Explained, the chimney pipe must be a minimum of three feet above the roof but also two feet taller than anything within ten feet. The portion of the rule stating the pipe needs to be 2 feet above anything within 10 feet is where most people get confused.
The "7 Times Rule" for chimneys dictates that the cross-sectional area of a masonry chimney flue cannot exceed seven times the area of the appliance’s vent connector (draft hood outlet) to ensure proper drafting and prevent acidic condensation. If the chimney is too large, it must be relined to prevent damage from cooling gases.
The chimney and flue open to the outside and thus can be a major source of lost heat. Rising heat could rush up through your chimney and out of your home. When thinking of ways to heat your home and save energy, stopping this heat loss is vital.
The largest source of heat loss in a typical house is uncontrolled air leakage (drafts), accounting for up to 38% of lost heat. Warm air escapes through hidden cracks and gaps, while the following structural areas are the primary culprits for escaping warmth:
Priming your chimney
All you have to do is light a rolled-up newspaper and hold it like a torch up the damper for several minutes. You should be able to feel the draft reverse once enough warm air has mixed with the cold air. Once you feel this reversal, you should be ready to light a fire.
This chimney construction rule says: The chimney needs to extend at least 3 feet above the roof on the side of the chimney where the roof is highest. The top of the chimney must be at least 2 feet higher than any part of the roof or any component on the roof that's within 10 feet of it.
The best solution to alleviating a cold chimney flue is to warm it up before you start your fire. This is often called “priming” your chimney. There are a couple of ways you can prime your chimney. For both ways, the first step is to make sure that your damper is open.
Yes, mice can absolutely come down your chimney. Because mice are agile climbers and can squeeze through openings as small as a dime, they easily scale the outside of a chimney and slip inside seeking warmth and nesting sites.
Additionally, in the early 1980's, tests were conducted to discover which kind of wood created the most creosote in a regular “open” fireplace. The results were surprising. Contrary to popular opinion, the hardwood's, like oak and poplar, created more creosote than the softwoods, like tamarack and pine.
Professional roofers possess extensive experience with chimney-related repairs that directly impact roof integrity and weatherproofing systems. Their expertise covers external chimney components including flashing replacement, crown repairs, and addressing problematic areas where the chimney penetrates the roofline.
Because they do not use standard grid electricity or conventional electric and gas furnaces, the Amish heat their homes using off-grid, self-reliant methods. The most common systems include wood- or coal-burning stoves, propane and kerosene heaters, and natural airflow home designs.
Turn Up the Heat: Tips to Follow
The net effect is that it can feel colder in the areas that are not directly adjacent to the fireplace. Even when the fire is not burning, you still deal with the fact that warm air rises. It will travel up and out through the chimney. Cold air comes in to take its place.
The worst firewood to burn falls into two categories: toxic and highly inefficient. You should never burn wood that produces dangerous chemical fumes or excessive smoke, nor wood that burns too quickly or spits hazardous sparks.
Circulate Warm Air with Fans
Using a ceiling fan on a low, reverse setting can help push warm air back down into the room. You can also use fireplace-specific blowers or fans designed to pull heat from the firebox and distribute it through the room more efficiently.
For a Hotter Fire
Fully open the damper to maximize airflow. It provides ample oxygen to the fire, resulting in a more intense and hotter burn. The damper must be fully open when lighting the fire.