Stains lighten as they dry, then return to their damp color when a finish is applied. So the quick method of seeing the color you'll get with the finish applied is to look at the stain while it is still damp.
Many, probably most, store-bought stains are made with both dye and pigment. If wood stained with these stains is exposed to sunlight or fluorescent light for a while, the dye color will fade away, but the pigment color will remain.
Leave the stain on the wood longer before wiping it off. This allows some of the thinner to evaporate and that increases the ratio of pigment to vehicle.
Staining wood is perhaps the best way to change its existing color. Traditional water-based wood stain penetrates the surface of the wood. This allows the natural grain and patterns of the wood to show through,while still changing it's color.
No, the sticky stains will not dry after some time, which is why it is important to wipe off the excess wood stain. If you don't, your work will end up sticky because the stain did not dry properly. You will have to use mineral spirits, more stain, or sandpaper to fix the mess.
Wipe the stain off immediately if you'd like a lighter tone. But for a deeper tone, leave the stain on the wood for 5 to 10 minutes before wiping it off. Be sure to wipe off all the excess stain going in the direction of the grain of the wood.
Using a lint free rag is the best way to apply wood stain because it is great for controlling the amount of stain that is applied and for removing any excess stain. Also, the rag leaves a beautiful, even, and brush stroke free finish. It also can easily be thrown out once finished.
The Cons of Staining Wood
While some stains can last up to five years, postponing re-staining a wood surface for too long can cause the job to become more complex and labour intensive. Even decks that are stripped and re-stained will still require maintenance every couple of years.
The new stain you are applying over the old stain should be compatible. For instance, if it's an oil-based stain, apply another oil-based stain. If it's a water-based stain, apply another water-based stain. Incompatible stains can lead to poor adhesion or blotchy and uneven finish.
Apply a second coat of stain after the first has dried fully. This will usually produce a slightly darker coloring with the excess wiped off. Substitute a glaze or gel stain for the liquid stain. Glazes and gel stains usually contain a higher ratio of pigment to vehicle.
Yes, each layer will darken your project even more. You can also start with a lighter color Gel Stain and layer on darker colors.
We always recommend two coats of stain for any wood project, but you should only apply as much stain as the wood can absorb. Extremely dense hardwoods may only be able to absorb one coat of wood stain. The general rule of thumb is to apply only as much deck stain as the wood can absorb.
Stains lighten as they dry, then return to their damp color when a finish is applied.
Why does this happen? Depending on the type of wood you're staining, the color of the stain can change. You have to take into account the hardness and undertones of the wood you're using. Both of these things affect the stain color.
If the first layer of stain looks perfect, then great! You do not need to add a second layer. You should reserve adding a second layer only if you want a darker color for the stain. However, many times, the first layer of stain will suffice for both adequate protection and the desired color.
Woods like pine, poplar, doug fir, birch, maple, Accoya, and cherry are some of the most problematic woods concerning blotchiness. These woods are unevenly porous, so they don't soak up stain consistently across the surface of a board creating an unpredictable uptake of color.
If you used a penetrating oil stain, you may have allowed the stain to build up too thick a coat on the surface of the wood. Penetrating wood stains are not intended to be a surface finish. If applied too thickly, they won't dry properly and will remain tacky to the touch.
Rubbing. Frantically rubbing a stain can make it spread further and also damage the weave of the fabric. Try gently dabbing the stain away first.
A common mistake when applying stain is not taking weather, temperature and moisture into account. Staining when the deck surface is too hot or the wood is too wet; when rain is too imminent or when nighttime temperatures are too cold can all lead to problems down the road and shorten the life of your stain.
Wood is dried-out and dull if you do not apply some sort of sealer. Staining and finishing are two very different things.
Sealing stained wood with Polycrylic
Polycrylic is a very popular sealant for wood projects. It is inexpensive and easy to apply. It provides strong coverage and is, in general, a great choice.
Typically, cold water works great on blood, as well as food, beverages and water-based paint, while hot water works best on protein-based stains. Unfortunately, there's no golden rule to stain removal. For example, most food stains should be soaked in cold water, unless it's egg, mustard or a tomato-based product.
Treat stain immediately. Soak 30 minutes or more in cold water. Rub detergent into stain. If stain persists, place a small amount of household ammonia on the stain and rub again with detergent.
Apply oil-based stains with a paintbrush or clean rag. Apply water-based stains with a foam brush or synthetic bristle brush. For deep grain woods, work the stain into the grain by working in a circular motion. Otherwise, apply the stain evenly in the direction of the wood grain.