Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Chlorine combines with the algaecide ingredients and renders them useless. The best time to introduce an algaecide , which functions best as a preventative, is after you've shocked the pool and the chlorine level has fallen below 5 parts per million.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
Your chlorine levels won't return to normal right after you shock your pool anyway, so we recommend waiting at least 24 hours to add algaecide. When adding algaecide to your pool, make sure you add the correct amount.
So unless you're dealing with mustard algae or black algae, leave the algaecide on the shelf and get ready to shock the heck out of your pool. But when dealing with regular ol' green pool algae, chlorine is your best bet to kill it dead.
Most products require 17g of non-chlorine shock per 1500 litres of water or 35g of chlorine shock per 1500 litres. Carefully pour the treatment into your spa near the water inlets. This will allow it to circulate evenly. Wait for at least 20 minutes before using your spa.
When a hot tub has been refilled, it is important to give the water a high dose of sanitiser. This can be done by adding 60g of chlorine granules per 1,500 litres of water to start the sanitation process and allow the level to drop to 3-5mg/l before using the hot tub.
The chemicals you will need to start your hot tub include a pH increaser, pH decreaser, calcium hardness, a metal removal (if using water from rainwater tanks or bore) and a sanitiser.
The honest truth is that every hot tub owner has accidentally over-shocked their hot tub at least once. It happens from time to time and it's not the end of the world. Try to keep it to a minimum, though, as it can damage your hot tub and actually harm your body, too.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
In a pool where algae is present, algaecides work in conjunction with chlorine to kill the algae cells. The algaecide causes the cells of the algae to burst, which destroys the plant. Different algaecides are used for different types of algae.
Add a dose of Salinity Multi-Purpose Algaecide to your pool 24 hours after shocking. Dilute the algaecide with water before adding it to the pool. Algaecide prevents and kills pool algae so your pool will look beautiful all the time. That's it.
Let the water circulate for at least two hours.
Circulate the water for about 2 hours to ensure the flocculant is fully mixed in, then shut off your pump and let it sit overnight. During this time, the chemical will start to bind the particles together and settle them to the bottom of the pool.
Regular hot tub shocking is inevitable to keep your water clean and safe for use. Dead skin and other elements like hair may end up dropping in the hot tub, leaving the tub in a mess. It is essential to shock the hot tub frequently – at least once every week.
The primary culprit of foam is failing to sanitize your hot tub water weekly or after heavy use, such as a hot tub party. Lotions, cleansers, makeup and even laundry detergent leave our bodies and swimsuits when we soak in water. Foam will appear if the pH balance of your hot tub water is off.
Chemicals in your hot tub water can be a delicate balance. So it's crucial to maintain the levels of pH, Alkalinity, and Chlorine or Bromine, also known as sanitizers. You should wait 12 hours before entering the hot tub when you've added either chlorine or bromine to allow it to take effect properly.
Add 1 oz. / 2 Tbsp of Shock to spa. Be sure to leave cover open and let spa water circulate for about 15 minutes while Chlorine/Bromine and Shock dissolve in to spa water. Afterwards, use a Test Strip to test levels following instructions of test strips (usually on bottle). Check Test Strip for calcium hardness level.
Generally it is recommended that you shock your hot tub once a week – more often if it's seeing heavy use. If your levels are all good, but the water is a bit cloudy or doesn't quite smell right, it's time for a shock. You should also shock the tub if you haven't used it for an extended period of time.