Now, here answers the question earlier: do you leave skimmer basket in when vacuuming pool? YES, you need to remove the skimmer or strainer basket before attaching the open end of the hose to the inlet. Finally, plug the open vacuum hose into the suction port.
ONCE YOUR VACUUM IS SET UP:
Water is now being taken out of the pool. If you have more than one skimmer, slowly close the valves. Ensure that the valve to the skimmer that the vacuum hose is connected to, is fully open. Slowly close the Main Drain valve about halfway, this is the optimal setting for vacuuming.
Remove the skimmer basket and push the end of hose into the suction hole. 4. Close any other skimmer valve and adjust main drain valve for proper speed. 5.
If dirt is reappearing at the bottom of your swimming pool after you've vacuumed it your pool's filter may be working poorly. Pool filters often work poorly because they're in need of cleaning. If you have a sand filter for your pool you need to make sure that the sand is sharp and freshened up.
Yes, we recommend backwashing after you vacuum your pool. This allows the filter to shoot out any dirt / debris you have vacuumed up. Don't forget to set your filter to “rinse” for 30 seconds after backwashing!
A vacuum plate fits on top of the standard-size strainer basket and incorporates a fitting that allows the vacuum hose to be plugged into the vacuum plate and receive suction from the inlet without removing the strainer basket. This reduces the potential of skimmer line clogs and expensive service calls.
When your pool skimmer has no suction, the cause is most likely a blockage. This can put the entire filtration system of the pool into question, as there will be low water pressure.
8. Vacuuming pool with filter valve in "backwash" position. When a pool is vacuumed with the sand filter valve in the "filter" position, the dirt and debris that passes through the pump ends up inside the filter on top of the bed of sand which is where you want it.
Above ground pool, vacuums and inground cleaners work the same way. Both harness the suction from your pool's filter system to suck dirt out of the pool. The brush head is used to scrape and scour the dirt, algae, and debris off the underwater surfaces.
Depending on the type of surface in your pool, you can use a brush to scrap it clean with or without water in it. If the pool has a soft vinyl liner, you will use a rubber or nylon brush to keep it clean. If the pool has a concrete floor and walls, a stiff and course brush will do the trick.
If the pool is too dirty for a swim, use a garden hose with a pressure attachment to lift debris off the bottom of the pool and into the water, where the filter can take care of it. If the water is very dirty, you may need to clean the filter system while cleaning in this way.
After the hose fills with water, backwash your sand filter for 2 – 3 minutes or until water runs clear. Shut off pump motor and push T-handle back down into locked position. Turn pump back on and note lower pressure.
Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter. Closed: if you choose this setting, then the flow of water to the pool and filter will be stopped.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Use the short pole for steps and shallow end walls, extend the pole for floor work. Brush Your Pool Starting at the Steps: Most pool vacuums will not ever touch your steps, and if your vacuum does, it will still need your help because this area is more vulnerable to algae and staining.
Remember: vacuuming your pool regularly will help keep your pH balanced easier and more controlled. Skim your pool for debris, such as leaves, bugs, etc. and be sure to check your skimmer and empty that regularly as well.
Use a pool brush to push all the sand to one area, or at least to a few concentrated areas. Set the filter's multiport valve to “Filter.” You can vacuum the sand back into the filter. Vacuum your pool manually, .
The most common connection locations are the open skimmer, suction port, or filter. An automatic pool vacuum system uses the pool's natural filtration system to clean it, so it could hook up to several ports since the entire pool uses the filtration system.