Usually no rinsing required. On wood surfaces, do not allow puddles of cleaner to remain. *Not recommended for use on unfinished, unsealed, unpainted, waxed, oiled or worn flooring. Test a small area first.
Finally, when used and applied the right way, Pine Sol doesn't leave behind any residue that will leave you with an unsightly hardwood floor surface. Wax and oil-based cleaners, on the other hand, leave behind a hazy residual substance.
The first option you can try is an ammonia-free cleaner like Windex. Spray a two-foot section of your floor and let the cleaner sit for about two minutes. Next, use a dish-scrubbing sponge to rub the section of the floor where you sprayed the cleaner.
First of all, the only hazardous ingredient listed on the Pine Sol MSDS is alkyl alcohol ethoxylates. These belong to a group of chemicals called "aromatic hydrocarbons" which are petrochemicals with strong, pungent, odors. The only health hazard listed on the MSDS is that it is an irritant.
Or for everyday mess control, keep the Pine-Sol® mixture in a spray bottle for quick cleaning spritzes. Scrub crevices in counters with grout with an old toothbrush. Scrub stubborn messes or stains with full strength Pine-Sol®, using plastic scrubbing pad or cloth. Finish by rinsing with water.
Pine-Sol® is not recommended for use on marble, aluminum, or unsealed, waxed, oiled or visibly worn wood.
Keeping your mop impeccably clean is essential, since even a little bit of leftover soil can result in a sour smell or breed bacteria. To keep yours in good shape, rinse the mophead thoroughly in a bucket of clean, hot (but not boiling) water immediately after mopping.
What is this? Pine-Sol is more acidic than Fabuloso, which gives it an advantage in breaking down stubborn stains and complex messes caused by grease. Pine-Sol Original is the only liquid cleaning solution that disinfects.
“And the floor can end up sticky and even dirtier because their cleaning solvent tends to dry very fast, leaving a sticky residue if not cleaned fast and well.”
Pine-Sol® Cleaners are concentrated formulas that you can dilute for most jobs. For general cleaning, a 24 oz. bottle gives you 12 gallons of cleaning power! Add water to the formula yourself and save.
Pine-Sol can help you with shower cleaning, walls, and more. Clear shampoo, soap and other items from your shower so you can hit all the corners before you clean. Mix ⅛ cup of Pine-Sol® in ½ gallon of warm water. Wipe down your shower walls with the mixture.
You can also use Pine-Sol® Original Squirt 'N Mop®. It's safe for wood and hard nonporous surfaces like ceramic and porcelain tiles, and also sealed granite. You can apply this product directly from the bottle over a 3' x 3' area and start mopping.
You're Using Too Much Product
If you're sure you've got the right product, but your floors still end up sticky, there might be another issue. Namely, it's important to properly dilute the cleaning agent with water. Otherwise, it will leave a sticky residue that's going to be even harder to clean.
A: Yes. Original Pine-Sol® Multi-Surface Cleaner is registered with the EPA as a disinfectant when used as directed full strength. When used according to the instructions on the product, it kills 99.9% of germs and household bacteria on hard, nonporous surfaces.
It is preferable to use cold water instead of hot water when mopping. The reason is that it does not damage the flooring and it retains floor shine. It also helps in eradicating germs and bacteria. Additionally, cold water saves a lot of electricity and leaves off a cooling effect later after cleaning.
Lysol can be hard to find online and in-stores, but Pine-Sol seems to still be available at most retailers. Compared to Lysol, Pine-Sol has a longer contact time (Lysol's ranges from 2 minutes to 5 minutes) but will still effectively help you to limit your contact with the virus.
Pine-Sol gives the same advice. PineSol.com states, “We do not recommend mixing any Pine-Sol® product with other cleaning products or chemicals. Mixing cleaners can result in the release of hazardous gases.”
Avoid Using Too Much Soap
Soap only lifts dirt and oil into water, making them suspend in water. Therefore, the more soap you use, the more your mop gets saturated with dirt. So, if you do not remove all the soapy water from the floor, the dirt remains, forming streaks on the floor.
Any high-traffic areas in your home should be wet mopped once a week. Rooms in your home that are not frequently used—such as a guest room—do not need to be mopped weekly. Mopping every other week or monthly should be sufficient.
Sticky floors occur when you leave behind too much cleaning solution, use the wrong floor cleaner, or not rinsing with clean water after mopping. You can clean the residue off tile and wood floors and then rinse using a clean mop and water. Clean with a steam mop to remove the sticky residue easily.
Steps For An Expert Clean
Mix ¼ cup of Pine-Sol® for each gallon of water. Dampen a soft sponge, cloth or mop with the mixture to wipe down the surface. Scrub stubborn spots with a gentle scrub brush or mop. Use Pine-Sol® full-strength if needed, following up with a water rinse.
A Pine-Sol® wipedown takes care of crumbs, cooking splatters and grimy corners for counters that sparkle. Nothing says "pristine kitchen" like an empty, de-gunked trash can. It's the perfect finishing touch for to get that Pine-Sol® clean and scent you love.
Many different scents of Pine-Sol now exist today that can fill your kitchen with a pleasant aroma. The cleaning solution can be used many surfaces, such as vinyl, tile, porcelain and other nonporous surfaces. Pine-Sol removes dirt and debris and it also disinfects floors, which makes it ideal for the kitchen.