Most top load washers made after 2001 do not have washer filters in their drainage system. Instead, newer models utilize a more powerful drain pump and larger drain holes. If you have a model made before 2001, you can usually find the washer filters at the bottom of the washer drum underneath the agitator.
Clean the Lint Filter
The lint filter in a top-load washer with a center agitator is inside the agitator. Newer washers with the agitator in the bottom of the drum may or may not have a lint filter. Some models rely on the water pump filter to do the work, while others have a mesh filter near the top rim of the drum.
Find the drain hose
Your machine will either have one drain pump filter by itself or a drain pump filter with a separate drain hose. In either case, these will be behind a panel on the front of your machine.
"The drain trap is usually easy to access and can be cleaned out periodically to ensure it continues functioning properly.” Although most modern washing machines do have a drain trap or similar mechanism, Smith suggests checking your owner's manual if you aren't sure.
“The drain trap is typically located at the bottom of the washing machine, near the drain hose, and is designed to prevent lint and debris from entering the plumbing system and causing blockages or damage,” says Smith.
It's usually a removable filter that you can access by lifting or pulling it out. The lint filter is usually positioned inside the front door on front-load washing machines. You can locate it by opening the door and inspecting the bottom-right corner.
Remove the drain hose attached to the back of the washer and check if it's clear. If you find any obstruction, you can rent an air compressor to blow air into the hose and clear the clog. But if the hose is worn or badly kinked, you may need to replace the hose.
Disconnect the hose from the machine and use a wire hanger or plumbing snake to remove any debris or buildup. After cleaning the drain hose, reconnect it to the washing machine and run a cycle to make sure everything is draining properly.
Most top load washers made after 2001 do not have washer filters in their drainage system. Instead, newer models utilize a more powerful drain pump and larger drain holes. If you have a model made before 2001, you can usually find the washer filters at the bottom of the washer drum underneath the agitator.
Start with an empty tub. For a front-load washer, put 2 tablespoons of borax or oxygen bleach and 2 tablespoons of washing soda in the tub of the washing machine. For a top-loading machine, put 1/2 cup of each of the powders into the wash tub. Run at the hottest temperature or use the “clean tub” setting on the washer.
You can typically find filters in top-loader machines in two places: inside the agitator or along the top lip of the tub. Here are tips on how to locate a washing machine filter in a top-load washing machine: Inside the center agitator: If you have a top-loading washer, inspect the center agitator.
Top-loading washing machine
In most top-loaders, the lint filter is either positioned along the top rim of the washer drum or at the end of the drainage hose. You may also find it inside the center agitator, which you can unscrew and remove. Check your owner's manual if you need help. Remove the filter.
Drano® Snake Plus Tool + Gel System was designed to unclog a kitchen sink, bathroom sink, shower, bathtub and even a laundry drain.
Use a funnel to pour about a quarter of a cup of baking soda into the pipe. Next, empty a baster full of vinegar into the drain hose. Top tip: If the blockage is not completely gone, you can repeat the above process. Once you have cleared any debris from the hose, pour hot water in to flush everything out.
Top-loading washing machines usually have a drain filter hidden behind a flap visible on the front side of the machine casing (example 1), or hidden in the threshold of the drum (example 2 - in this case the threshold of the drum has a special recess that allows it to be lifted up).
Pull the Washer Out from the Wall
To drain a top-load washing machine, you will need access to the back of the washer, where the drain line is located.
A washing machine not draining can have multiple causes, including a clogged or jammed drain hose or a broken pump, lid switch, or belt. No matter the culprit, you need to drain the water from the washing machine before diagnosing the issue or doing any work to remedy the situation.
Do Maytag Washing Machines Have Filters? All modern Maytag washers have filters that should be regularly cleaned every 3-6 months to prevent harmful lint buildup or clogs. In top-loading machines the filters are in the center of the agitator tube.
Start a hot wash cycle and allow the drum to fill completely with water. Once full, add a quart of chlorine bleach to the machine and allow the cycle to complete. Run a second cycle through the machine, adding a quart of distilled white vinegar to the drum after it's filled with hot water.
In models without an access door, the coin trap is found deeper in the drainage system by the drain pump. There may be a lower access panel or one on the top of your water, but usually, you will need to remove shell of your washer in order to reach it.