Radiators need a thorough inspection at least once a year, the best time being just before the start of the winter. Any professional plumber can do this, but it is advisable to make it a part of the annual gas safety check, which needs to be done by a gas-safe registered engineer.
A plumber can work on your heating system (radiators, pipework etc), but cannot work on the boiler or the gas pipe. The main difference between a plumber and a heating engineer is that a plumber does not carry any gas safe qualifications.
If your vehicle's radiator fluid level is low or you need to replace it, bring your vehicle to your local Jiffy Lube®. The trained technicians can test the vehicle's cooling system, assess your needs, replace your radiator fluid (if necessary), and properly dispose of your old fluid.
If you've got a problem with your radiators or heating system then it's usually best to call in a professional plumber or heating engineer. While there are some jobs that you can do yourself, it can be difficult if you don't have any DIY experience.
However sometimes a leak in the radiator needs to be fixed by a plumber, and occasionally even replaced fully. It is important to get them fixed as soon as you can, as it wastes water and can make your radiator not work properly.
While the process of balancing radiators can be relatively simple, it can be daunting to do if you've never done it before. This is where a professional heating and plumbing expert can help.
Yes. Most radiator leaks can be fixed by a qualified plumber or even a competent DIYer. More serious problems, however, such as a leaking radiator that also struggles to warm up, may require a system power flush or even a radiator replacement if the system is too sludged.
Hiring a plumber to remove a radiator can cost anywhere between £80-150. If you're looking at getting the radiator replaced, this will incur further costs. Of course, if you feel confident with the process, then you can have a go at removing it yourself.
If you require a professional to install the replacement radiator valves, you may also need to factor in the cost of labour. This can vary depending on the location and complexity of the installation, but you can expect to pay around £50-£100 or £40 to £60 per hour.
Powerflush is the process of using a specialised device to pump cleaning chemicals into your system, circulating them and removing the unwanted material from the system itself. The chemicals are pumped at a high pressure to ensure any rust, corrosion, sludge, or miscellaneous debris is effectively removed.
A licensed HVAC technician can tell you if it's a power supply or safety issue related to your heater, or if it's a larger electrical issue that an electrician will need to address.
Ensure your cooling system performs for years to come by getting an expert radiator flush and engine coolant change at Jiffy Lube®.
We highly recommend that you hire a professional plumber to move a radiator. If done incorrectly, you run the risk of water damage or flooding, as well as damaging the radiator, heating system and walls.
While plumbers focus on pipes and fixtures, HVAC technicians focus on all heating and cooling systems in the home.
Radiator. Inspect the exterior for leaks and signs of corrosion, clogged fins and plugged or damaged overflow tubes. Pay close attention to any clues indicating a previous repair. Look inside the radiator fill neck for signs of oily deposits, which could indicate a blown head gasket.
Depending on the severity of the damage, you'll need to budget around $300 to $2000 to replace a car radiator. Labor expenses will range from $75 – $150 (per hour) for services, including mechanic inspections for leaks, removing the old radiator, flushing the entire system, and installing a new radiator.
Want to find out how much bleeding a radiator costs? Everything you may want to know about bleeding your radiators is covered in this guide, including the labour costs and time frames you should expect. To give you a quick idea, the average cost to bleed a radiator is usually about £100.
Radiator replacement
Each radiator takes about 2 to 2.5 hours to replace with like-for-like, plus the system drain-down and refill time (see above). Consequently replacing 3 radiators is typically a full day's work.
Who should I call to fix my radiator? If your radiator is not working or some of the units are not heating up, then your best action is to call a qualified plumber or Gas Safe-registered heating engineer.
Age. The average lifespan of modern radiators is between 10 and 15 years. Older radiators become less efficient, and even if they are still working perfectly after 15 years, they are more likely to develop problems, for example, internal corrosion.
It's recommended you consult the services of a professional plumber for this task to ensure the work is done safely and in line with Building Regulations. Balance the system - When completely removing a radiator from the system, you'll need to balance the heating system before you start using it again.
Replacing a radiator valve is not a difficult task, but it can require a little bit of technical know-how, so as always, we recommend that you seek the help of a heating engineer if you're unsure or lack DIY experience.
If your radiator is severely damaged, it may need to be replaced entirely. This is a more involved repair that will take longer and cost more than a minor repair. In some cases, it may not be worth repairing the radiator at all; if the damage is severe enough, it may be best to simply replace the entire engine.
You can absolutely replace a radiator yourself. It's a challenge, but with the right tools and some basic knowledge, an untrained layperson can do it without a mechanic. Cars can be complicated machines, and your car's engine bay might have hundreds of precisely fitted components.