Running your filter after shocking your pool is a must and is just as important to your pool as shocking it is. Be sure to run your filter for at least 6 hours, but shoot for 24 hours to several days, if your pool is particularly dirty or has algae, to properly circulate the chlorine and clean the water.
It's best to shock your pool once the sun goes down and when the pool filter is running. If you put the shock in while it's sunny out, it will not work as well. Never shock your pool when people are swimming in it.
Run the filtration system
While shocking your pool will help kill any germs any algae, it won't actually get rid of them; for that, you need your filter. So be sure to run your pool filter for at least 24 hours.
Answer: After shocking the pool, it will need filtration and circulation. Run the pump as much as possible. Keep the filter clean (daily) until the water runs clear. Be sure to brush the pool often during this process as above-ground pools do not have drains at the bottom.
Now it's time to wait a while.
Keep your pump and filter running. Give the shock a good 12 to 24 hours to work it's magic. If the algae hasn't cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.
The ideal time to shock your pool is in the evening after all swimming is complete. In the evening because the sun will not be boiling the chlorine out of your pool, and after everyone is done swimming because shocking is going to bring the chlorine level up to a level that may be irritating to skin and eyes.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
You should cover your pool every night for several reasons. First off, a pool cover saves energy and conserves water by decreasing the amount of make-up water. Also, it reduces the consumption of chemicals, and finally, it saves a lot of cleaning time since it keeps the debris out of the pool.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
SKIMMER NOTES: No. Chlorine and shock are not the same thing.
Shock has a more intense chemical strength than the traditional chlorine sanitizers, and it also differs in how you should apply it to your swimming pool. Short answer: No. Chlorine sanitizers and shock are similar but different in strength.
Never pour pool shock into the skimmer, pre-dissolve for use in vinyl liner pools. When broadcasting shock across the surface, be mindful of the wind direction. Brush the pool after shocking, and filter the water for at least 8 hours afterward.
Find out the volume of your pool. This will give you an idea of how much shock you need. The general recommendation is to use 1 pound of cal hypo shock for every 10,000 gallons of pool water, and 10 ounces of sodium hypo with around 12.5% chlorine to sanitize your pool. Make sure the pool water is at its normal level.
Pre-Dissolve Pool Shock
If you need to dissolve the shock first, fill your bucket roughly ¾ full with warm water. Add the shock to the bucket, and slowly stir until the chemical is as dissolved as possible.
You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool. As a reminder, you want your pH to be between 7.2 and 7.8ppm and your free available chlorine to be 1-4ppm for safe swimming.
Heavy rains will deplete many of the chemistry levels in your pool. Generally your alkalinity will drop significantly. It is a good idea to have Alkalinity, Muriatic Acid, Chlorine (or Salt), and Shock on hand to be able to test your water and treat your pool immediately after the rain stops.
The blue material is translucent, which allows UV rays to pass through the cover and into the pool and does well enough to block heat from escaping the pool.
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.
It's best to run your pool pump during the day
Not only does sunlight give fuel for algae to grow, it also destroys your pool chlorine and this is why you should always run your pool during the day!
One of the most significant consumers of energy in homes with swimming pools are pool pumps, which keep pools clean by circulating water through filters. Pool pumps can consume 3,000 to over 5,000 kWh per year.
If your pool pump manufacturer has declared your pump is rain safe, you can leave it on in rainfall. Nevertheless, during a thunderstorm, it is highly recommended that you switch off and unplug your pool pump to prevent any costly and irreversible damages to your pool equipment.