Adding chlorine besides the shock can increase the chlorine content in the water which can make the entire shocking process useless. Hence, it is better if you don't use the shock and chlorine at the same time. The best time to add chlorine to the pool water is after you have shocked the pool.
You should wait one hour per pound of shock product added, and then test the water to confirm the pH and chlorine are in the proper range before letting anyone enter the pool. As a reminder, you want your pH to be between 7.2 and 7.8ppm and your free available chlorine to be 1-4ppm for safe swimming.
If your total chlorine level is high, you will use a non-chlorine shock; if it is low, you will use a chlorinated shock. As a rule, you will need to raise free chlorine to 10 times your combined chlorine to hit what is known as “break point.” Therefore, it is good to deal with combined chlorine while it is still small.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
After the pool shock is added, pool toys and accessories can also be thrown in for decontamination. Never add pool shock directly to the skimmers. Keep the pool uncovered until chlorine levels return to normal. NEVER swim before checking to make sure the chlorine levels are at 3 ppm or less.
A pool filter should be run for a minimum of 6 hours after shocking a swimming pool. This is to allow the filter to clean the water and give the shock enough time to fully mix with the pool water. Running the filter after shocking for 24 hours to 7 days is necessary if the pool has a large amount of algae.
After Shocking Your Pool
It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours. It is always best to test first!
The best time of day to shock your pool is in the evening. This is because the sun's rays can affect the effectiveness of the chlorine by dissolving it too quickly, before it has a chance to rid the pool of contaminants and clean the water.
Shock is chlorine, in a high dose, meant to shock your pool and raise the chlorine level quickly. Chlorine tabs (placed in a chlorinator, floater, or skimmer basket) maintain a chlorine residual in the water. You do need to use both tabs and shock.
The Bottom Line about Pools and Chlorine
As mentioned above, you could probably swim in a pool without chlorine without any major health issues. However, long-term use of a pool lacking chlorinated H2O could make you sick or, at the very least, contribute to rashes and other types of skin irritation.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Heavy shocking with granular chlorine will generally require 24-48 hours before the chlorine level has dropped to safe swimming levels (below 5 ppm). Lithium and Non-Chlorine shock labels typically allow immediate swimming, but check the package label, to be sure.
You should never add chlorine and muriatic acid at the same time. The muriatic acid will react with the chlorine in your pool and create a deadly gas called hydrochloric acid. You need to wait for a minimum of 30 minutes, after you add the acid, before adding any chlorine to your pool.
Alkalinity Adjusting Chemicals for Pool Start Up
This should be the first chemical that you add to your pool during start-up. This one can really affect the pH level of your pool. Sorting this out first prevents you from ruining your hard work on your pool's pH level by doing it afterward.
Adding more chlorine to your pool will kill bacteria, pollutants and any other unwanted organisms in the water. Most people wait until they have a cloudy pool or pool algae to shock their pool. However, adding shock to your pool on a regular basis can help you avoid pool water problems.
If the pool is still very cloudy or green, you may need to shock it to make it safe to swim in again. First, make sure that the filter system is working properly and the chemicals are still at the proper levels. Next, mix up your chlorine shock (hyperchlorinate) treatment.
Before you start pouring shock in the pool, the first step is to brush the sides and floor of your pool to loosen all the algae. Doing this breaks the skin and allows the pool shock to more easily kill the algae. Once you've done this, it is important to make sure you have the proper pH level in your water.
Light Green or Teal Pool Water:
In this case, you should double shock your swimming pool water. To double shock, you will need to add 2 pounds for every 10,000 gallons of water. For instance, if you pool is 20,000 gallons, you will add 4 pounds of shock.
Give the shock a good 12 to 24 hours to work it's magic. If the algae hasn't cleared up after 24-48 hours, clean and brush the pool and add another shock treatment.
It's best to shock your pool once the sun goes down and when the pool filter is running. If you put the shock in while it's sunny out, it will not work as well. Never shock your pool when people are swimming in it.
The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.
Having too much chlorine in your pool water can be dangerous. Exposure to high levels of chlorine can cause lung irritation, skin and eye damage, and provoke asthma. Not only is it bad for your health, but it can be bad for your pool due to the increase in chlorine.
The most important factor though is the size of the pool. You'll need about 52-104 oz of liquid chlorine per 10,000 gallons of water. This amount should get the chlorine level to between 5 and 10 ppm.