The sooner you can get your cuttings into a more normal environment with air flow and no dome, the better off they'll be. After about a week, remove the dome and monitor your cuttings to see if they begin to wilt. If they do, they're not ready to go dome-less, so try again in 1-2 days.
Several cuttings can be placed in the same pot as long as their leaves do not touch. Enclose the pot in a plastic bag, making sure the bag does not touch the leaves. Place the pot in a warm, bright spot but out of direct sunlight. Every few days, check the rooting mix to make sure it is damp, and water as necessary.
Keep your cutting humid by loosely wrapping it in clear plastic. You can also create a makeshift greenhouse by placing the entire pot in a clear plastic bag. Place your planted cutting in bright light but avoid direct sunlight which can be too powerful.
Cuttings can take in water from the air through pores in the leaves called stomata. To trap humidity, plant your cuttings in wet soil, use a spray bottle to mist the leaves, and cover them with clear plastic as described before. Then, place your cuttings in a warm spot.
Technically, you can transfer your cuttings to soil at any time. In fact, you can actually propagate directly into soil, however, it's much harder to do within your home. When you propagate in soil, you have to keep a good balance of soil moisture, air flow, and humidity.
Carefully remove excess leaves to reduce transpiration, so cuttings do not wilt. However, some foliage should be retained to allow photosynthesis to occur. Keep cuttings moist, cool and shaded (collecting in a damp plastic bag is a good idea) until you are ready to put them in a propagation medium.
Warm growing medium temperatures accelerate cell division which leads to faster callusing, root initial development and subsequent root growth. It also speeds up the dry-down rate of the growing medium, which also helps encourage better rooting. The best way to warm the growing medium is through bottom heat.
In general, the rooting medium should be sterile, low in fertility, drain well enough to provide oxygen, and retain enough moisture to prevent water stress.
Cuttings need water for hydration, but also enough oxygen for roots to respire and grow. Using a substrate with adequate air porosity, and using the 1 to 5 moisture scale can help to prevent overwatering that leads to slow rooting and increased risk of disease.
-Don't make the mistake of thinking that a plant can remain covered for a few days when the weather calls for more than one night of frost. The protection needs to be taken off every morning when the sun comes out. Plants can't breathe under a heavy container, a layer of plastic or fabric.
Plastic will transmit cold air to the plants, causing more harm than good. We recommend using cotton fabric or frost cloth to protect plants from frost.
Give cuttings bright light but not sun. Keep soil moist but not wet. The cuttings should root within three weeks. Admit air gradually to wean the cuttings from their humid environment, then pot singly before outdoor planting.
From stick to root development (Stages 1-3), propagators sometimes use too little water or moisture, but most often provide too much water, which leads to leaching and waterlogged propagation substrates (Fig. 1), uneven rooting and loss of cuttings due to rot (Fig. 2) or botrytis.
Place your stem cutting in your vessel with enough water to cover the node. The water level will drop due to evaporation, so you should add water every 3-5 days as needed. You can watch the roots develop if you have chosen a clear vessel for your cutting.
Try to wait until at least 50% of the cuttings have good rooting before potting them up; however, for some hard-to-root species, you may be lucky with only 10% to 20% success.
Some plants will root in water, but cuttings will develop a better root system when rooted in a soil-less potting mix. Sand or perlite can also be used, especially for cuttings that need good drainage and may rot if kept too wet.
Cuttings are very delicate and vulnerable so pests, disease, the wrong growing conditions, too much water or too little water can all cause them to fail.
Several cuttings may be placed together in one container. Be sure to add fresh water as needed until the cuttings are fully rooted. Rooting will generally occur in 3-4 weeks but some plants will take longer. When the roots are 1-2 inches long or longer the cutting is ready to be potted up.
Auxins stimulate root formation on the stem cuttings, e.g., IBA, IBA-alanine, NAA. NAA is synthetic auxin while IBA is considered as both natural and synthetic.
Add your cutting, and then mist the surface thoroughly daily (trying not to get the cutting). Twice a day if it's hot or dry. By 'mist' I mean properly wet the surface of the soil. Every week or so, stick your finger in the soil further down, and water it 'properly' if it's dry.
Storage of cuttings
It is best to harvest cuttings in early spring and plant immediately but if this is not possible, cuttings can be stored safely for about 4 months. Store cuttings in a cool, dark, and moist place.
Warmth is important and bottom heat, in particular, will encourage rapid root formation. fungicide types. stress will encourage root development.