For most patios, brick pavers are the go-to flooring of choice. Clean these up properly by applying hot steam with the main jet nozzle attachment of the steam cleaning unit. This will allow you to cover a wider surface area, and effectively get out any mud and dirt that might be caked onto your pavers.
A steam or pressure washer, which can be hired, will give your paving or patio a really deep clean. Work your way over the surface of your patio removing as much grime as possible. It's best to sweep the pressure washer back and forth over the surface, as it's a powerful jet and can cause damage.
Mild detergent and water.
Mix some mild dish soap with water in a bucket to create suds, then use a brush or a sponge to scrub the surface of the pavers. If your pavers are textured or have intricate designs, this cleaning method can be gentler than a power washer.
There are useful tools for cleaning paving stones, such as joint scrapers, sweepers, and pressure washers. In addition, pavers can be cleaned with a small pickaxe, broom, and garden hose.
Use a specialist cleaner
Try a specialist cleaner like Wet & Forget, at Walmart, which you spray onto the surface of the paving and leave. It can also be used on steps, fountains, patio umbrellas and other smaller outdoor areas. It's bleach-free and non-acidic but will remove mold, moss and grime without any scrubbing.
Cleaning pavers with bicarbonate soda and vinegar
Fill the bucket with lukewarm water and then add the bicarbonate soda, making sure it dissolves properly. Then add a little bit of white vinegar. Pour the solution onto the stained areas on your paver surface and use the scrubbing brush to apply it thoroughly.
Yes, you can pressure wash your pavers. But while using a pressure washer at a basic level is simple, ignorant and inexperienced users can easily damage their pavers by using a stream that's too powerful, by holding the wand too close to the pavers, or by falling into any number of other rookie mistakes.
To clean paver slabs, you can use a detergent, such as Dawn, or a vinegar-water solution that is gentle enough to effectively clean without causing damage to your concrete pavers.
The best way to clean the patio and your outdoors is with a steam cleaner. A steam cleaner will be able to fight against stains, grease, and more due to its high heat and high pressure combination. Steam will not damage the surface of your patio but it will successfully remove any stubborn dirt.
You can use a steam cleaner. Many people assume steam cleaning is only effective indoors, but it is actually very effective for outdoor spaces. Before you begin outdoor cleaning with a steam system, you need to prepare. Start by moving furniture, grills and other items from the space you are going to clean.
Steam cleaning is perfect for removing dirt and grease, or to restore the shine to polished concrete floors more effectively than using a dust mop or even a damp mop. The superheated water creates a dry steam that is safe on polished concrete and will remove dirt without damaging the floor finish.
Baking soda is an amazing household cleaner, and it can work really well on your pavers too.
It is common to mix bleach with water; however, you can also add other ingredients to make it more effective. Similar to cleaning pavers with muriatic acid, avoid an intense concentration of bleach, as it can damage the pavers.
White vinegar is good for cleaning pavers, though it's also acidic enough to erode the stones' surface. Diluted vinegar can be used safely to clean paving stones, though it should be used sparingly and infrequently to protect your paving from damage.
After you have invested in pavers, whether that be a patio, poolside deck, etc., it is important to seal your pavers in order to protect from the weathering UV rays. These rays, which are known to impact the skin negatively, also impact the surface of your pavers negatively.
1000 to 1500 psi pressure is easy to mange and will not cause damage to pavers and paving stone. A low pressure washer is also safe for mortared flagstone and slate patios and walls.
Try Concrete Stain
The simplest path to reviving tired pavers is to apply an acrylic-based semitransparent concrete stain, such as Behr Premium Semi-transparent Concrete Stain ($27/gal.; Home Depot) or Valspar Semi-transparent Concrete Stain ($28/gal.; Lowe's).
Simple Green is one of the best cleaning products for dirty pavers. It doesn't have any harmful chemicals that could possibly warp your precious driveway. Less chemicals mean there's a less likely chance your paver stones will change to a weird-looking color.
Pour baking soda on the stained spot, then add a bit of warm water. You can add some detergent or white vinegar for a stronger vinegar solution. Let the mixture sit for at least 1 hour. Scrub the top of the pavers, with extra attention to the gaps between the stones or bricks.
Using a product like PROSOCO's Cleaner/Degreaser first will remove oil stains from the surface of your pavers and reveal any stains that have penetrated deeper into the pavers. To remove deeper-set stains, a product like Oil & Grease Stain Remover is a better option.
Whether your patio is sealed concrete or cement, or even sealed concrete pavers, a bleach and water solution makes it easy to clean away built up soil, stains from leaves and pollen, mold, mildew and algae.