While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
It's important to know that using pool shock and algaecide together can create bad chemical reactions if you don't take the necessary precautions. Your chlorine levels won't return to normal right after you shock your pool anyway, so we recommend waiting at least 24 hours to add algaecide.
Algaecide should be added to your pool water on a weekly basis. Preventing algae is the key to fun in your pool. Algaecides act as a backup to your normal sanitization program and prevent algae from starting and growing in the pool. Algaecide should be added after every shock treatment.
The presence of too much algaecide can lead to a foamy pool water. Small bubbles will begin to be produced as the water is pushed through the return jet and back into the pool. Do not confuse these bubbles and foam with another common problem, which is air in your pool lines.
Add a dose of algaecide, bring your chlorine level high by shocking, and run the filter continuously until the problem clears. The next day you should vacuum up the dead algae and backwash your filter. Algae thrives in hot weather and in pools with low or no chlorine.
If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy. If the cloudiness persists 24 hours after shocking, then it's possible that you used a poor-quality chlorine shock.
While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM.
Alkalinity Adjusting Chemicals for Pool Start Up
This should be the first chemical that you add to your pool during start-up. This one can really affect the pH level of your pool. Sorting this out first prevents you from ruining your hard work on your pool's pH level by doing it afterward.
You should not add all pool chemicals at the same time. You should also avoid mixing pool chemicals together. Adding chemicals at one time can cause dangerous chemical reactions and serious injuries. In addition, it will make it difficult to balance the pool.
High doses of chlorine, like pool shock, can cause temporary cloudiness as it kills contaminants. High levels of pH, alkalinity, and calcium hardness are more likely to cause cloudy water.
Pools can immediately turn green after shocking when they have metals like copper in the water. These metals oxidise when exposed to high levels of chlorine which makes the pool water turn green. Adding a metal control product such as Zodiac Metal Remover will help to restore the pool water.
Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.
What's important for you to know: You shouldn't swim in a pool that's green until you test the chemical levels, like the officials in Rio did before the diving event began. It's the balance of things like chlorine, pH, and alkalinity in a pool that keeps it sterilized.
Adding a recommended dose of shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
Skim the top of the pool for debris that may have settled on the pool surface. Add one pound of diluted granular shock to the water for every 7,000 gallons of pool water. Run the filter for 24 hours and retest the water. The slimy looking film can be an early onset of algae.
It's pretty tough to over-shock your pool; shocking your pool two days in a row with the proper dosage for your pool volume shouldn't be a problem – and in fact, is sometimes even needed to rid your pool of algae and other contaminants.
In most cases, a cloudy pool after shocking is only temporary and should clear up within 24 hours. Keep filtering your pool, add a little clarifier to help, and your pool should be clear in no time. If after 24 hours your pool is not clear, then you may need to look a little deeper for the solution.
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.
Incompatible Pool Chemicals
Mixing of organic chlorinating agents (such as trichloroisocyanuric acid) and inorganic chlorinating agents (such as sodium hypochlorite) can lead to fires, explosions and chlorine gas release.
Undissolved Granules
The presence of these granules does not indicate that you have added too much stabilizer -- the product is slow to dissolve, particularly when static. You can speed the process by agitating the granules with a brush so that they circulate in the pool water.
Chlorine is a common disinfectant that is widely used in swimming pools and leisure centres. Chlorine should not be stored with ammonia, acetylene, benzene, butadiene, hydrogen, any petroleum gases, sodium carbide or turpentine.