I asked Bryan if he could give us some insight on what it takes to actually remove a coat of sealer from concrete. He recommends starting with 2,000 psi and stepping it up to no more than 4,500 psi. The temperature of the water varies but is vital in this removal method.
The first, and in our opinion easiest, way to remove concrete sealer is a powerful pressure washer. If it's powerful enough, the pressure of the water will easily strip away any type of concrete sealer. If a pressure washer isn't an option, certain chemical strippers are also quite effective at removing sealer.
FastStrip Plus is a Solvent-Based concrete sealer remover that can be used to remove old sealers before repair or resurfacing. Most concrete slabs are not immediately ready to receive a new coating or overlay. Most have a pre-existing coating on them that must first be removed before any new product can be applied.
An effective pressure wash cleans the pores of your concrete. Make sure to apply concrete sealer after pressure washing.
Yes, because a pressure washer is 30-80 times stronger than your hose, it can cause damage if used improperly. If your concrete becomes etched during the pressure wash, you should stop before causing further damage and reduce the pressure.
When the sealer is applied too heavily, the air displaced through the surface can't escape, and it forms a bubble in the sealer surface. Bubbling of a sealer can also occur if application is done in hot weather, or if the concrete is in direct sun.
However, vinegar isn't strong enough to remove concrete sealant. Sealants can resist acid, and vinegar is a much weaker acid than chemical removal agents. And worse, vinegar can damage concrete by dulling it and causing pitting.
Smooth Concrete Sealer Basics
Penetrating Sealers soak into porous concrete and masonry and create a permanent chemical reaction. They offer a flat appearance and protection that will only wear away if the substrate itself wears away below the level of sealer penetration.
Acrylic Concrete Sealers: Acrylic sealers last 1-3 years before they need to be re-coated. Epoxy Coatings: Epoxy coatings last 5-10 years before they need to be re-coated. Urethane Coatings: Urethane coatings last 5-10 years before they need to be re-coated.
A simple floor stripper or paint and epoxy remover is something you can use to remove asphalt sealer. A caveat, though: you can only use paint and epoxy remover on concrete, metal, wood, and masonry. Do not use this on vehicles and walls as the product could strip the clear coat or paint off.
The easiest way to remove a concrete sealer is to begin by acid etching the surface of the concrete with muriatic acid. This process can be dangerous if you are unfamiliar with it; however, it is well within the ability of any ordinary homeowner, as long as the proper care is taken.
Soda blasting, a less aggressive mechanical method, has become more widely used in recent years to remove sealers and coatings successfully. Soda blasting utilizes special high-pressure blasting equipment with commercial-grade baking soda granules as the blasting medium.
Cleaning concrete with muriatic acid can be a highly effective solution if used correctly, providing ultra-bright white concrete and removal of many types of stains. In one application, you can remove rust stains, oil stains, algae, and paint splatter with a quick chemical application followed by pressure washing.
The standard solvent bath process involves spraying store-bought xylene or acetone across the problem area. (As a side note, I do not recommend acetone, as it dries too quickly to be effective.) You wait a few minutes to allow the solvent to liquefy the sealer, then wipe or roll the area to eliminate the problem.
Yes, vinegar is an excellent concrete cleaner. This solution can strip surface-level messes from concrete. Due to its acidic properties, vinegar can be a powerful tool for breaking down offensive materials such as dirt, stains, and bacteria.
While the advantages outweigh the negatives, there are some disadvantages that you should keep in mind before sealing your concrete driveway. Sealant can make the surface slippery. Sealants tend to dry down with a glossy or semi-glossy sheen that can be quite slick, especially when wet.
Over time, heavy coats of sealer lose adhesion to the concrete surface and flake off.
In fact, vinegar removes mold from concrete better than bleach. Bleach will only remove the top layer of mold, causing the mold to return.
Whether they're petroleum-based stains, grease stains, or something you can't quite identify, we have a cleaner for you. Overall, we recommend Zep Purple Pressure Wash (US$13.98, The Home Depot). Alkaline cleaners are great for lifting oil stains, grease stains, and other petroleum-based stains from concrete.