To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.
Use an off-set laminate trim router and a template to cut through the laminate first, following the cutout dimensions. Then you can cut the substrate any way you want without chipping the laminate - like cutting butter with a hot knife!
You can get pieces of different lengths that you can cut down to the exact size you need. This method will work for cutting all types of laminate countertops, including Formica. You can also use the same method to cut solid wood countertops, such as butcher block countertops.
You can cut laminate countertop with a circular saw and a fine-tooth carbide blade. Run painter's tape along the cut line on the top surface, so the cut goes down the middle of it. Turn the countertop over. Mark and cut it from the back side so the saw teeth pull into the top surface.
Countertop Width Standards
Most homes are fitted with kitchen countertops that measure 25.5 inches in width (from the wall to the edge of the counter), with some measuring up to 28 inches.
Standard Countertop Width Measurements
The average kitchen countertop measures 25.5 inches wide (going from the wall to the counter's edge). Some measure up to 28 inches, but you usually won't find any wider than that. Standard measurements allow for a 1.5-inch overhang over 24-inch deep base cabinets.
Laminate flooring is available in different plank thicknesses and widths. Plank thickness can range from 6mm to 12mm thick, and width can be from 3 to over 6 inches.
The key to cutting through laminate flooring without chipping it, is to use a fine tooth blade. Some recommend at least 18 teeth per inch on a hand saw to prevent chipping, whilst others recommend at least a 30 teeth per inch blade for a jigsaw.
Countertop Installation
Slabs are either cut off beforehand or on-site by skilled fabricators to fit pre-taken measurements. This includes crafting custom edges and making cutouts for under-mount sinks and cooktops.
Yes, IKEA's custom countertops can be cut to whatever size is needed. You may need to measure your kitchen counters to work out what sizes are needed. They offer standard sizes that can be altered.
To cut the Formica® non-décor magnetic laminate board, TCT circulate saw blades should be used with a minimum of 60 teeth per blade with a tooth thickness of 1.8mm. The diameter of the blade should be 305mm. Saw blades with a negative hook are also recommended.
We can professionally cut laminate worktops to size, in both width and length. By using equipment of only the highest quality, we can guarantee an accurate and perpendicular cut. Our machinery is regularly serviced to maintain the high standards of our worktop cutting service.
Score the broken edge with a utility knife. Use the iron to heat up the broken piece, then pry it off. Hold replacement piece of laminate edging against the countertop edge and iron it on. If the glue doesn't reactivate, adhere the replacement piece with contact cement.
To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front.
When you need this, it is wise to cut the materials first and then laminate. That way you can get a secure seal around the whole edge rather than cutting afterwards and leaving the potential that the laminate could lift. If you laminate then cut right around the material it may also leave the end unprotected.
A jigsaw is a real all-rounder when it comes to cutting laminate floors. It's best used to cut out shapes from your board. For example, when you want to place boards around your toilet or maybe a pillar. Always use a fine toothed blade and have the saw blade spinning before you touch the board.
The Secret to Make a Straight Cut on the Laminate Countertop
A circular saw with a blade made of fine-tooth carbine does this job the best. A jigsaw with a fine-tooth blade can also be used. For this, you will need to cut from the countertops' bottom side using the up-cutting blade.
The maximum overhang is no more than 1/3 of the total dimension of the countertop – not to exceed 12”. Overhang greater than 12” requires corbels or flush mounted steel supports. Supports must be designed to bear the weight of the countertop and be mounted to studs or equivalent load bearing structure.
When laying laminate flooring it is essential that you leave at least a 10-12mm expansion gap around the perimeter of the floor. There are important reasons to do so, and we will cover them in this article.
Thicker laminate floors are easier to lay, quieter to walk on and are better to hide small irregularities in the subfloor. We find that most people prefer to lay a 12mm thick laminate in high-traffic areas.