Most low-flow showerheads have a rubber pressure-reducing valve (called a regulator) to maintain a lower pressure. You can increase the flow by simply taking it out. You could also consider enlarging the hole that allows water into your showerhead with a drill to increase the amount of water coming through.
Removing the water restrictor from your showerhead can also improve water pressure. Removal might also clear out mineral build-up around the restrictor. It's fine for you to remove one if you live in an apartment unless otherwise stated. Note that your water bill may increase after removal.
For water conservation purposes, most plumbing codes require faucets and showering devices to not exceed a certain maximum flow rate. Removing the flow restrictors could cause these devices to no longer meet these codes.
Do All New Shower Heads Have Flow Restrictors? Not all new shower heads come with flow restrictors. While many brands focus on water and energy efficiency, it's not a universal feature. So, before you make a purchase, it's a good idea to check the specifications and ensure they fit your needs.
Two big reasons: To help lower utility bills -- and to conserve water. According to the EPA, the average family could save 2,700 gallons per year by installing WaterSense labeled showerheads. Since these water savings will reduce demands on water heaters, they will also save energy.
Removing a flow restrictor is illegal according to the US Energy Policy Act of 1992, which limits the maximum shower water flow rate to 2.5 gallons per minute (GPM).
A standard 2.5 GPM shower head uses 2.5 gallons of water each minute. That's 25 gallons for a 10-minute shower. VS. A low-flow 1.8 GPM shower head uses 1.8 gallons of water each minute.
A quick and easy way to increase water pressure (for homes supplied by a municipal water system) is to adjust the pressure-reducing valve, which can be found on the main water-supply pipe; look for a conical-shaped valve next to the water meter, close to where the main water pipe enters the house.
Leaky, corroded and clogged pipes can lead to low water pressure in the shower. The showerhead might be so old it needs to be replaced. The shower controls could also be responsible for flow issues.
If your water pressure seems low, the first step should be to test how much pressure you're actually getting from the shower head. A typical home's water pressure should be somewhere between 45 to 55 psi (pounds per square inch).
The most common cause of low shower pressure is a blocked showerhead, as a result of limescale build-up. These blockages obstruct the water flow, leading to reduced pressure over time. Most showers are fitted with a filter, protecting the pipework from debris, but this can become partially blocked by scale.
U.S. government regulations limit the maximum flow rate of shower heads to 2.5 GPM as a measure to save water. Some places that experience droughts and water shortages have even tighter restrictions.
What does a flow restrictor look like? Before you remove the flow restrictor from your shower head, you need to know what it looks like. A water flow restrictor is usually a flat, circular, plastic piece. The center of the restrictor is shaped like a star, or similarly shaped, and comes in a variety of colors.
Please keep in mind that all new faucets since 1994 are restricted to conserve water per EPA code mandates. Older faucets had no restrictions. Beyond intentional flow restriction, new installations can sometimes have reduced flow if the lines are not flushed prior to installation of aerators or shower heads.
After all, it needs certain amount of water to remove the soap, that is physic. Studies have shown that 1.8 gpm is the minimum flow rate to have a good enjoyable rinsing, so the common 1.75 gpm models, is somewhat good enough for a decent shower. To save water further and still have a full enjoyable rinsing experience.
Install Flow Restrictors
Flow restrictors belong on all bathroom and kitchen faucets. Each one can save you up to 5,000 gallons, or about $10 every year.
Flow restrictors limit the amount of water flowing downstream, while pressure regulators affect the pressure of upstream water by changing the flow of downstream water. Water pressure regulators are not designed to control flow rate. However, they affect flow rate by managing the pressure within a water line.
If you're looking for the most pressure, go for the 2.5 GPM Flow Rate, unless you are restricted because you reside in California, Colorado or New York. Again, this has been the Maximum Flow Rate since 1992. The step down from there in Flow Rate is 2.0 GPM.
Normal psi for a home pipe system is between 30 and 80 psi. While you don't want the psi to be too low, it violates code to be above 80. Instead, you should aim for a psi that's between 60 and 70.
Install a Pump for Pressure
You will want to boost the pressure in this situation, thus the overhead water tank pressure pump should be installed on the discharge line. The pump will be able to raise water pressure as well as the amount of water that enters the pipe from an overhead tank in this manner.
Loosen the lock nut on the pressure reducing valve with a wrench and back it off by unscrewing it. Fit a socket wrench over the adjustment nut on the top of the valve. Turn the nut counterclockwise to reduce the pressure downstream from the valve and clockwise to increase it.