Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Backwashing a filter too frequently will keep the sand so free of dirt buildup that it will not have the ability to remove the smaller particles of dirt and they will simply pass through sometimes causing cloudiness in water.
Low flow = poor circulation which will lead to algae in the pool. Bottom line, the filter must be backwashed on a regular basis to ensure that your pool water is clear. "When do we need to backwash?" - It is recommended to backwash your filter once every 4-6 weeks of regular use.
Typically, you should backwash a pool if the pressure gauge on your filter is at 8-10PSI at the starting level. So, to answer the question of how often should you backwash your pool, check your PSI. If the filter runs well at 16PSI and then goes up to 25PSI, your pool needs a backwash.
DE filters are usually torn down and cleaned at least six times per year. Unless your pool gets really dirty, you should not need to backwash it beyond your scheduled maintenance. Another theory recommends to backwash when the pressure gauge is about 8 to 10 psi (pound-force per square inch) over the starting level.
How Often Should You Backwash a Pool Sand Filter? As a general rule of thumb, you should backwash and rinse your filter about once a fortnight. The optimal time is right after you vacuum the pool. However, if your pool has had a lot more use than normal, it may be necessary to backwash once a week.
You should backwash your DE pool filter about once a month during pool season. In addition to the regular schedule, you'll want to perform additional backwashing if: You've been running your pool filter for 48 hours straight. This can cause a pressure build-up, even if the filter grids look clean.
Too much sand and your filter will likely not run correctly or may break when reassembling. Too little sand and you will have cloudy water no matter how much your filter runs.
Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds. Stop the pump and turn the lever to FILTER. This is the normal operating position. Close the drain outlet valve and start the pump.
The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value's waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.
It is not recommended to drain a swimming pool through the backwash valve. While sucking from the main drain and putting the water down the backwash line will work in some scenarios it puts your pool pump at risk of losing prime and running dry.
Your filter may be clean and normal at 9-10 psi, but your neighbor's filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
In unsewered regions, backwash water is to be discharged to a grassed, vegetated or garden area, or a stone-filled trench either open to the surface or underground (similar to a septic tank absorption field).
When you first install a sand filter or renew the sand, you may indeed get a small amount of sand coming out when backwashing, rinsing or filtering. Often, excess sand gets into the wrong places when refilling and will sand to come out into the pool or out of the backwash hose. But it should go away after a few runs.
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
Add diatomaceous earth (DE) to your pool skimmer, stick to around a scoop or two – no more than the size of a 1lb coffee cup. The moment you do this, go to the pool jets to see if it is returning DE into the pool, or if the water suddenly looks cloudy. If it is, you likely have an issue with your filter.
The 'Rinse' setting should be used after backwashing and again run just for a minute or two. On this setting the water is flowing through the filter in the normal direction but once again is being sent to the waste pipe rather than being returned to the pool.
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
Rinse runs water in the same direction that normal filtering does. Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
When do I need to replace my sand? On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
The most likely cause of sand at the bottom of your pool is that it simply fell in the water. This can happen even if you don't have sand around your pool. Wind can pick up sand particles and carry it long distances. So the wind may have dropped some sand in your pool on the way through the neighborhood.
If your swimming pool begins to seem a bit cloudy or unclear, then you may have a sand filter that's running slowly. This can happen even though your sand filter looks fine and seems to be running as it should. It can look like how it's supposed to but not be filtering debris from your pool as it should.
Do not operate your filter pump without having the D.E. powder coating the grids, or you will see the filter pressure rise very quickly, and if left in this manner the grids can collapse or the fabric can become clogged or damaged. As the pressure gauge on a D.E. filter increases, flow rate decreases.
The rule of thumb is generally 8 hours, although it could be anywhere from 6-12 hours, depending on your pool's size. Each pool is unique, so to keep your pool pump efficient and effective, you need to figure out exactly what your pool's turnover rate is.
The most common reasons why a cartridge, sand, or DE filter's pressure rises quickly, even after cleaning or backwashing, is a clogged or blocked filter, algae or old filter elements. If any of these things are wrong, the pressure can rise rapidly in minutes, hours or days.