Never add chemicals at the same time, whether you're balancing the water, shocking the pool, or adding a specialty chemical. For most water balance changes, the pump needs to run on the high setting for at least four hours before you can add another chemical or retest the water.
Some clarifiers are polymer based and the shock can act to break up the polymer causing the clarifier to be ineffective. It's best to shock your pool before and wait a day or two before adding clarifier.
It Should Not Be Done Together. While shocking and adding algaecide is effective in getting rid of algae, it should not be done together. This is because when you mix chlorine and algaecide together, it renders both of them useless.
Despite being chlorinating agents, they are incompatible. Do not add at the same time or mix muriatic acid and chlorine. Such interaction produces a toxic gas that is dangerous to health even in small amounts. A good rule of thumb is to never mix pool chemicals with each other.
Balance It Out Then Mix It Up
To get the best results from pool clarifier on the first try, make sure your pool filter is in tip-top-shape, that you've checked your pool chemistry, and that your pH and chlorine levels are in the right place. Now you can add the clarifier and go for a swim!
What happens when you add too much clarifier is that all the little particles clump together too much an end up as a colloidal suspension. When that happens, the whole thing turns cloudy. It'll clear but it will take a while. Run the filter 24/7 until is clears.
When should Pool Clarifiers be Used? Pool Clarifiers are not meant to be used all season long, but are quite helpful at pool opening, after an algae bloom, or battles with cloudy pool water. Follow label directions, but most pools can be retreated after 5-7 days, with a lower dosage than initially used.
Chlorine is a common disinfectant, is widely used in swimming pools and leisure centres. Chlorine should not be stored with ammonia, acetylene, benzene, butadiene, hydrogen, any petroleum gases, sodium carbide and turpentine.
ADD POOL CLARIFIER
The change in your pool water colour means that you have successfully eliminated the algae and can now clean it out of your pool. If your water is still green, wait another 24 hours and redo the steps from Days 1 and 2.
Adding a recommended dose of shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
If there is algae, brush it off of the walls and floor. Clean the filter then shock the pool. After that, add the phosphate remover. Keep in mind that phosphate remover is hard on the filter, and you will notice reduced flow after a day or two.
Cloudy or milky water after shocking is normal, and the water should clear up within an hour or so. Just make sure your pump and filter are running properly. If you add algaecide, keep in mind that some algaecide contains copper, which can actually make a pool cloudy.
To maintain a clear sparkling pool add 4 fluid ounces of Water Clarifier per 10,000 gallons of water weekly. If the pool is cloudy due to dust or to high hardness of the water, add 32 fluid ounces of Water Clarifier per 10,000 gallons of pool water.
Don't mix them in the same container. In the pool it's okay because of the water volume (the products are diluted more). But NEVER mix them both in the same bucket or chlorinator.
Never, ever mix types of pool shock.
Mixing liquid chlorine or even dry chlorine granules can cause a volatile reaction. Add each chemical to your pool separately. Do not add shock directly to the pool water unless instructed to do so. If the package says dissolve before adding, make sure to do just that.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool.
First, balance total alkalinity because it's like an umbrella measurement that can help protect pool conditions and keep chemicals levels in check. Raise total alkalinity with baking soda or soda ash and lower total alkalinity with muriatic acid. Aim to get total alkalinity to a range of 80 to 120ppm.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.