The simplest answer is no, it is best to avoid bleach when cleaning any type of natural stone.
Many home cleaning products, especially bleach, are way too strong or acidic to be on natural stone. These products can strip your natural stone down, leaving it damaged and weak. Whenever your natural stone becomes damaged, the damage cannot always be repaired.
Just use soap, warm water, and a non-abrasive cloth or sponge. Thoroughly scrub the entire surface with soap and water. Rinse the sponge, repeat with a clean, damp sponge to remove soap residue, and then dry with a soft dish or hand towel.
Clean stone surfaces with warm water and a mild soap such as a clear Dawn Liquid Soap. Do not use products that contain lemon, vinegar or other acids on marble or limestone.
Acidic commercial cleaners and those containing harsh chemicals, like bleach, can damage and dull natural stone surfaces.
It's essential to only use cleaners which are appropriate for natural stone surfaces. This means avoiding using vinegar. Stones like limestone, marble, or travertine will react to vinegar because it's an acidic cleaner with harsh effects.
You should not use Lysol on your granite countertops, backsplashes or vanity tops. The cleaner contains harsh ingredients that can cause your sealer to lose its effectiveness. In specific, scents such as lemon contain citric acid, so you need to keep away from those.
Bleach, vinegar, the ingredients in Lysol, and others can cause permanent damage, especially if used incorrectly. Acids, such as vinegar and even lemon juice, can break down the sealant that is used on stone countertops. Clorox and Lysol sprays and wipes are convenient, but they are not safe for granite countertops.
Containing both ammonia and lemon, Lysol Lemon All-Purpose Cleaner isn't a good option for cleaning granite countertops. The acid in lemons is known to break down the sealant used to protect granite countertops. In addition, ammonia can scratch the surface of your granite and even start eating away at it.
Diluted hydrogen peroxide works well on Sandstone, Marble, Bluestone, and Travertine. In the case of Granite floor, simply brush the area in dry condition. No solution is required to cleanse moulds or algae from Granite floor.
Apply a paste of baking soda and water over the stain and leave it for 24 hours. Gently scrub the area and rinse it with plain water. Stains on Sandstone pavers, Travertine floor tiles, and Marble floors can easily be cleaned with a baking soda solution.
Keep It Simple to Clean Natural Stone
You can use any type of mild soap detergent, such as dish or hand soap, and mix it with a little water. Wet the stone first, and then use a bristle brush and soap solution to wipe the stone clean. The last step is to make sure you rinse thoroughly.
To maintain the luster and shine of your natural stone, use a stone-safe polish about once a week. To polish stone, simply spray the polish directly onto the surface, then buff the surface until it's dry with a lint-free cloth or dry paper towel.
Clean stone surfaces with a few drops of neutral cleaner, stone soap (specific products from Lithofin for example), or a dishwashing detergent and warm water. Use a clean soft cloth for best results. Too much cleaner or soap may leave a film and cause streaks.
Sulfamic and phosphoric acids are the safest and most used acids used in solving tile and grout cleaning problems. These two acids have very specific mixing and application recommendations that must be followed to the letter. Regardless, thoroughly rinse the cleaned area, dry, and polish.
Our Stone Cleaning Process
First we scrub grout lines with a pre-spray. Then we extract dirt and grime from the stone using a high-pressure rotary wand. Finally, our 3-step polishing process uses a series of buffer pads to polish your stone, removing etching and light scratches.
Combine about 45 grams of baking soda with about a liter of water and mix well in a medium-sized bowl. Use a clean cloth to apply the mixture to the surface. Allow the paste to dry for about 5 hours, then use a microfiber cloth and warm water to rinse. Dry buff with a clean microfiber or chamois cloth.
Clean with a microfiber towel or nylon pad.
To avoid detrimental scratches, clean tile and stone with softer sponges. Nylon, microfiber, and soft brushes will help clean stone without damaging its sealant. You can also keep a microfiber towel near the shower to easily soak-up and remove excess water after each use.
Quartz is an incredible material and easy to clean.
The beauty of natural stone with the durability of a manufactured one. For heavier stains, glass or surface cleaners will do the trick since quartz is non-porous and you don't have to be as finicky with the pH as you would with granite.
And in this case, this mixture does not work well with the natural stone countertops. Due to the fact that vinegar is acidic substance and baking soda is caustic, the result of mixing the two can have an unstable effect on stones that are porous.
Not sealing a stone countertop or floor tiles — which get the heaviest traffic and are the most susceptible to wear and tear — leaves the surface vulnerable to absorbing foreign substances, which can weaken the stone and potentially lead to the growth of bacteria.
The Difference Between Manufactured Stone and Natural Stone
Natural stone is heavier in weight, making it difficult to transport. Manufactured stone requires less installation time while also being cost-effective. Manufactured stone creates less waste than natural stone. Manufactured stone adheres to multiple surfaces.