Can A Saltwater Pool Be Used on an Above Ground Pool? If you're wondering if a saltwater generator can be used for an above ground pool, the answer is- absolutely! Many people have above ground saltwater pools, especially as salt water pools slowly become the norm.
The chlorine produced by salt is a higher quality than the traditional chlorine. By converting to a salt pool, you no longer need to purchase chlorine tablets, liquid chlorine, or shock.
6000 ppm or higher can cause corrosion to metals in contact with the water. For a newly constructed pool or freshly plastered finish, it is recommended to allow the pool surface to cure for 30 days prior to adding salt (Sodium Chloride = NaCl).
When your salt levels are low, you can just add salt, but when they're too high, you have to dilute the water similar to what you do if you have a high cyanuric acid level. If you need a more accurate guide on how much salt you need to your specific Intex pool, check out this page from The Pool Factory.
To maintain a salt water pool you'll need to keep your filter, pump, and skimmer clean and in good operating condition. With salt water pools, you must inspect the salt chlorinator cell and replace it when needed. Test regularly for proper water chemistry to maintain clean, clear pool water.
Adding salt, without a SWG, gives the water what many people describe as a silky feel, but it doesn't give you any of the other advantages of a SWG. For example you can't use lower FC levels with salt the way you can with a SWG.
To reach the initial salt level recommended by the salt system manufacturer (usually 2400-3200 ppm), you will need to add about 200 lbs of pure pool grade salt (NaCl), per 10,000 gallons of water. Salt stays in the water, you only need annual boosters, to replace salt lost to backwashing or splashout.
As shocking has a tendency to push metals out of solution and salt (even when labeled as pure) can contain trace amounts of metals, it is recommended that you add salt at a different time from shocking. Have your PH and ALK within range when adding salt, and brush until it is completely dissolved.
You will want to use NaCl, sodium chloride, of at least 99% purity. To add salt, turn on your filter pump and add the salt directly to your pool water. Use a brush to help the salt dissolve and to prevent the salt from piling up on the bottom of your pool.
When you add salt, DO NOT pour it directly into the skimmer. For best results empty the required salt into the shallow end of the pool and let it dissolve and circulate through the main drain. The salt may take about 24 hours to dissolve completely. Finer grades of salt will dissolve faster.
Electrolysis: electrolysis is a sound alternative to chlorine. The salt electrolysis device converts salt (NaCl) into chlorine and lye. The benefit of this method is you no longer need chlorine, which automatically means that the characteristic chlorine odour in and around the swimming pool goes away.
Superchlorinate after rainstorms or heavy pool use, but for algae, chloramines or contamination, you will need to use packaged pool shock. In summary, shocking a saltwater pool is no different than shocking any other chlorine pool.
Wait until the shock process is complete, then put in the salt. It'll dissolve right away and be ready for the SWG by the time you get ready to use it.
While green algae are endemic in salt water pools, they are the easiest to kill. Green algae tend to grow during summers when the temperatures can get high. They float freely in the pool, making the water green. You might even see them growing on the bottom of the pool, on the walls, or in the crevices.
Unlike chlorine, pool salt is actually just standard NaCl, sodium chloride. It is really just table salt in a different form. The primary difference is that pool salt comes in a larger cuts or sizes. The two chemical elements that comprise pool salt are sodium and chlorine.
You need a special pump and filter to run a salt water pool. There is no such thing as a “salt water pump” or “salt water filter”; any pool pump or filter will do just fine.
Can I put Epsom salts in my spa pool? In short, no. You should never put Epsom salts in either your spa or swim spa.
This increases the salt content in the body, raising the blood pressure of patients with salt-related blood pressure and may cause heart attacks, ”said Meriç, adding that although swimming regularly has health benefits in all aspects, this is not true for some people.
Pros of Saltwater Pools
There's less chlorine and less of the heavy chemical scent and content. They're gentler on the skin, with less irritation to the eyes, hair and swimsuits. The water has a softer, silkier feel to it compared to chlorine water. They have lower maintenance costs than chlorine pools.
This start-up investment may be recouped in a few years with less expensive day-to-day chemical needs. A saltwater pool requires less than $100 a year in salt and chemicals if it is consistently maintained. A chlorine pool, on the other hand, will cost between $300 and $800 per year in maintenance chemicals.
Generally, it's recommended to wait about 10 minutes between adding each pool chemical. Some pool chemicals like pool salt and cyanuric acid take longer to dissolve in the pool water. The aim is to avoid strong concentrations of chemicals mixing together.
There is no set timeframe of when you need to add salt to your pool. Because salt does not dissipate from your water, the only time you would add salt to your pool is when you add fresh water or after heavy rain that dilutes salinity levels.
The pool's salt chlorinator creates the right amount of chlorine needed to keep your water clean, according to Hayward. While there are reasons to add extra chlorine to your saltwater pool, you must do so carefully. Too much chlorine with salt water is never a good combination.