A quick and easy way to increase water pressure is to adjust the pressure-reducing valve, which can be found in your home, usually close to your water meter. If your pressure gauge reading was low, make slight adjustments to your regulator.
Adjust the Pressure-Reducing Valve
Protruding from the top of the valve is a threaded bolt. To raise pressure, loosen the bolt's locking nut, then turn the bolt clockwise. Use the pressure gauge to determine when you reach a water pressure around 50 PSI. Then, tighten the locknut to secure the valve.
A fast drop in only one faucet means there's a problem with the faucet. Rapid low pressure affecting one area of the house may mean a corroded pipe issue. An abrupt water pressure drop affecting the whole house may mean a water main break (municipal water) or a well pump problem (well water).
It may be caused by debris such as dirt, sand, solidified oil and grease, food particles, or foreign objects. Pollutants can block pipes if they back up due to fractures in the water main. Mineral buildup clogs pipes over time and causes the water pressure to go down, as there's less space for water to travel through.
If you have low water pressure in all your plumbing fixtures, the issue is almost definitely with your water supply or your pipes. However, if it's one or a few fixtures that seem to have a low flow, you may want to check out the fixtures.
Check Your Aerator
If you have especially hard water, aerators become clogged with hard water buildup, a common cause of low water pressure in kitchen fixtures. Clean your aerator for a quick and easy DIY fix. Remove the aerator from the faucet using pliers and a towel (to prevent scratching).
If there's an accumulation of sediments in your hot water tank, it can lower your water pressure. The presence of kinks in the flexible water pipes used in water heaters can result in low water pressure. If the shut-off valve isn't fully open, water pressure can drop.
Too much water pressure can be dangerous but low water pressure has an equal potential for being dangerous. Low water pressure could also mean that you have a clog somewhere in the system that you need to resolve. You want to do it fast because this can lead to issues with leaks that can cause water damage and mold.
Water pressure regulator replacement: $250 to $1,000. Pipe section replacement: $500 to $4,000.
Typically, water pressure regulators cost about $50 to $100 on average1, though you could end up paying up to $2001 depending on the size of incoming water line.
To return to full pressure only takes seconds. Flushing and recirculating takes minutes if you open all the taps, with the exception of tank water heaters.
Do I need a water pressure regulator? Building code requires that homes that receive water with pressure greater than 80 PSI have a water pressure regulator. A home's water pressure should stay in the range of 40 to 60 PSI.
Do All Homes Have a Water Pressure Regulator? No, and in some cases, you may not need one. Certain municipal supplies regulate their water pressure safely, but if that pressure runs above 80 psi, you'll want to protect your plumbing system by installing one.
Some of the first signs of a failing pressure regulator are a leaking water heater or commode. The water coming from a faucet may also exit with such force that splashing or water “hammering” may occur.
Remove and clean the faucet aerator thoroughly, or replace it with a new one. Remove and clean the flow restrictor, increase the size of the flow restrictor hole, or remove it entirely and replace the aerator without replacing the flow restrictor.
In most cases, the easiest way to increase a faucet's flow rate is by replacing the aerator. Try looking for a higher gpm model to allow for more gallons per minute. If you live in a low water pressure area, an aerator designed to restrict water flow might be reducing the flow too much.
Find the spigot closest to your source of water. Make sure all the taps and other water uses are turned off in your house. Now turn on the spigot and see how long it takes to fill the bucket. Dividing the number 60 by the time to fill the bucket will give you the gallons per minute number.
If the low water pressure seems restricted to a single faucet or showerhead, the problem isn't with your pipes or water supply, but with the fixture itself. If it's a sink, the most common causes are a clogged aerator or clogged cartridge.
If the municipal water or well-water flow is the problem, hire a licensed plumbing contractor to install a water-pressure booster pump. These powerful, electric pumps target incoming pressure and raise it to the proper level.
The most common cause of poor water pressure in the home is blockage somewhere in your sewer line. If your home's septic system includes a private septic tank, call a plumbing specialist to inspect your home's tank to see if the unit needs to be drained.